plainsman Posted November 1, 2016 Report Share Posted November 1, 2016 Is there a knack in refilling the greaser? I 've tried spooning it in and sticking the greaser barrel into the grease tub and 'sucking' up the grease by winding back the piston. Whatever I try I still get air trapped in the greaser. Any suggestions? Link to comment Share on other sites More sharing options...
Scholar Gypsy Posted November 1, 2016 Report Share Posted November 1, 2016 There are loads of other threads about this. Personally I take both ends off the barrel, and push the new grease in using the disk in the grease tin. I only fill it about 2/3rds full as that makes less mess. Then put the top back on, and then refit. Link to comment Share on other sites More sharing options...
Neil2 Posted November 1, 2016 Report Share Posted November 1, 2016 (edited) Take the top off the greaser so it's a tube open at both ends, push tube down on grease tin until grease comes out of the top. Screw the top back on. Edit - sorry SG beat me to it. Edited November 1, 2016 by Neil2 Link to comment Share on other sites More sharing options...
Chewbacka Posted November 1, 2016 Report Share Posted November 1, 2016 I wind the piston back about 20mm, then use a bit of wood about 3mm thick and 30mm wide - I guess a spatula would be fine - to push some grease in, wind back another 20mm more grease etc. Link to comment Share on other sites More sharing options...
Jak Posted November 1, 2016 Report Share Posted November 1, 2016 Simples! Link to comment Share on other sites More sharing options...
Tony Brooks Posted November 1, 2016 Report Share Posted November 1, 2016 No to all the above. Take the tube off the bottom foot but keep the screw turned down. Hold the open bottom firmly over the hole in the disk in the can (as per the open both ends method). While maintaining moderate downward pressure with one hand unscrew the screw with the other. Grease will be drawn into the tube and fill it up. No mess at all unless you tip the tube and disk. Link to comment Share on other sites More sharing options...
Victor Vectis Posted November 1, 2016 Report Share Posted November 1, 2016 I've tried Tony's method and it didn't work. I reckon it depends on getting an air tight seal between the foot of the tube and the disk in the tin. The 'open at both ends and shove it down' method did it for me. The only trouble I had was screwing things back together. The thread used is quite fine, compared with the diameter of the tube, and quite easy to cross thread. Link to comment Share on other sites More sharing options...
beerbeerbeerbeerbeer Posted November 1, 2016 Report Share Posted November 1, 2016 Trapped air will work its way out. That's always been my experience. Link to comment Share on other sites More sharing options...
Laurie Booth Posted November 1, 2016 Report Share Posted November 1, 2016 Is there a knack in refilling the greaser? I 've tried spooning it in and sticking the greaser barrel into the grease tub and 'sucking' up the grease by winding back the piston. Whatever I try I still get air trapped in the greaser. Any suggestions? Is your gun removable ? Mine is not. I will explain if your gun is the same as mine. Link to comment Share on other sites More sharing options...
plainsman Posted November 1, 2016 Author Report Share Posted November 1, 2016 Is your gun removable ? Mine is not. I will explain if your gun is the same as mine. By gun you mean the brass cylinder? If so mine screws off completely from the base as does the other end with the plunger. I've tried Tony's method but doesn't work for me. Link to comment Share on other sites More sharing options...
Chewbacka Posted November 1, 2016 Report Share Posted November 1, 2016 I can't use the hole in the disc in the can method as I have a big tub of grease and it doesn't have a disc. Link to comment Share on other sites More sharing options...
alan_fincher Posted November 1, 2016 Report Share Posted November 1, 2016 No to all the above. Take the tube off the bottom foot but keep the screw turned down. Hold the open bottom firmly over the hole in the disk in the can (as per the open both ends method). While maintaining moderate downward pressure with one hand unscrew the screw with the other. Grease will be drawn into the tube and fill it up. No mess at all unless you tip the tube and disk. Works for me. (Usually!) Link to comment Share on other sites More sharing options...
pquinn Posted November 1, 2016 Report Share Posted November 1, 2016 Just wondering, does the grease go off over time? Link to comment Share on other sites More sharing options...
Cheshire cat Posted November 1, 2016 Report Share Posted November 1, 2016 I've found Tony's method doesn't work for mere mortals. Air gets past the plunger. Lots more grease in the tube if you open both ends. I agree about the risk of cross threading too. Carefully does it. Link to comment Share on other sites More sharing options...
Rob-M Posted November 1, 2016 Report Share Posted November 1, 2016 I can't use the hole in the disc in the can method as I have a big tub of grease and it doesn't have a disc. I have the same trouble, no disc. Therefore I add a small amount of grease and push a length of wood through it which seems to let the air escape and then push some more grease in and repeat until I decide I've put enough in. Link to comment Share on other sites More sharing options...
Scholar Gypsy Posted November 1, 2016 Report Share Posted November 1, 2016 I have the same trouble, no disc. Therefore I add a small amount of grease and push a length of wood through it which seems to let the air escape and then push some more grease in and repeat until I decide I've put enough in. Do you then put the greasy stick into your stove? Link to comment Share on other sites More sharing options...
Rob-M Posted November 1, 2016 Report Share Posted November 1, 2016 Do you then put the greasy stick into your stove? No I keep it with the grease tin and use it again next time. Link to comment Share on other sites More sharing options...
AndyV Posted November 1, 2016 Report Share Posted November 1, 2016 Now, this may be a stupid idea, and I have certainly never tried it because I use the spatula and mess method, but would it be possible to melt the grease, perhaps in hot water, and just pour it in and let it cool. Link to comment Share on other sites More sharing options...
Dinz Posted November 1, 2016 Report Share Posted November 1, 2016 One way https://www.youtube.com/watch?v=-ewL1mbcnMc Not my way i have to say. Link to comment Share on other sites More sharing options...
Scholar Gypsy Posted November 1, 2016 Report Share Posted November 1, 2016 One way https://www.youtube.com/watch?v=-ewL1mbcnMc Not my way i have to say. was that a silver butter knife ?! Link to comment Share on other sites More sharing options...
Laurie Booth Posted November 1, 2016 Report Share Posted November 1, 2016 By gun you mean the brass cylinder? If so mine screws off completely from the base as does the other end with the plunger. I've tried Tony's method but doesn't work for me. Sorry, I meant the brass cylinder. Yours is not the same as mine. Link to comment Share on other sites More sharing options...
Dinz Posted November 2, 2016 Report Share Posted November 2, 2016 was that a silver butter knife ?! I believe Hudsons have one issued as standard Link to comment Share on other sites More sharing options...
Tony Brooks Posted November 2, 2016 Report Share Posted November 2, 2016 I've tried Tony's method and it didn't work. I reckon it depends on getting an air tight seal between the foot of the tube and the disk in the tin. The 'open at both ends and shove it down' method did it for me. The only trouble I had was screwing things back together. The thread used is quite fine, compared with the diameter of the tube, and quite easy to cross thread. All I can say is it has worked for me across a range of boats. I suspect those who fail may either not be putting enough downward pressure on the disk in the grease tin or their hands wobble. Otherwise the open both ends is the way to go. If you are using the spatula and blobs of grease method you are likely to trap a considerable amount of air in the tube along with the grease. This makes refill times come around faster. Link to comment Share on other sites More sharing options...
Jrtm Posted November 2, 2016 Report Share Posted November 2, 2016 (edited) As my tube has been modded and only winds down i do this. (All i did was take the secure nut off the bottom of the shaft where it connects to the disc) I unscrew it from the base i unscrew the shaft till it comes out. (Just the shaft not the top) I push the pressure disc up inside to the top Now as i have a big tub of grease i just use a small scraper to fill the tube and air is let out the hole threw the disc and out the top. You can use a container with a hole in and just sit the greaser over the hole and push down still let the air out threw the hole. Now once filled (you know its full as the grease comes threw the hole a tiny bit) Now put the shaft back in it will then push against the disc screw it till it moves the disc the use your scraper to level off the bottom and attach back to the base. + if someone unscrews my greaser it has no effect on the system dosnt move the disc so no grease gets sucked out the line it just dosnt add any in just a fail safe incase someone uses it but not sure as to what there doing. Atleast i know no grease is sucked out. Ive not had a problem with air so far. I should add you should be able to use tonys method has worked for me in the past but as im making my boat so friends fam can just turn up turn on the main electric and go boating im making it as idiot proof as possable. Hence my modded greaser. Edited November 2, 2016 by billybobbooth Link to comment Share on other sites More sharing options...
Chewbacka Posted November 2, 2016 Report Share Posted November 2, 2016 ......................If you are using the spatula and blobs of grease method you are likely to trap a considerable amount of air in the tube along with the grease. This makes refill times come around faster. Not if you unwind 20mm at a time, though it does take about 5mins to fill it. I agree if you fully unwind and start pushing grease in you will end up with about 75% air. Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now