carp-addict Posted June 5, 2023 Report Share Posted June 5, 2023 Hi all I am looking for advice I am in the process of decommissioning my pump out toilet. The tank will remain in situ for the foreseeable but I need advice for the best way to clean out the inside with a view that eventually it will dry out inside without any odours. Is this something that can be achieved Regards Link to comment Share on other sites More sharing options...
Bod Posted June 5, 2023 Report Share Posted June 5, 2023 What is your tank made from? Steel or plastic. Bod Link to comment Share on other sites More sharing options...
carp-addict Posted June 5, 2023 Author Report Share Posted June 5, 2023 Hi Bod It's made of steel and as far as I know it has an inspection chamber Link to comment Share on other sites More sharing options...
Tracy D'arth Posted June 5, 2023 Report Share Posted June 5, 2023 Pump it out, flushing if you can. Then dose it with Jeye's Fluid, a gallon will be ample, fill it completely with water and let it stand for a week before pumping out. If there is a port, vac it out with a wet 'n dry vac and let it dry out. 1 Link to comment Share on other sites More sharing options...
Bod Posted June 5, 2023 Report Share Posted June 5, 2023 (edited) The top of a steel tank can be very corroded, but the bottom and sides are often "pickled" in that the tank contents have done no harm, but may have preserved the metal somehow. Check very carefully the state of the tank top, if it's not sound, then complete removal may be the only way to stop smells. Be aware the bottom of the tank may be the base plate of the boat, so don't cut it out! If it has an inspection plate, then it's in with a hose pipe and scrubbing brush, followed by pump out and rinse. This is the true meaning of D.I.Y! Bod Edited June 5, 2023 by Bod 1 Link to comment Share on other sites More sharing options...
David Mack Posted June 5, 2023 Report Share Posted June 5, 2023 (edited) When I removed Belfast's steel pumpout tanks they had been emptied with a normal boatyard pumpout machine, with some extra rinsing. When I came to remove them a few months later there was about an inch of liquid inside, which was pretty inoffensive. There was a little sludge in the bottom, but that seemed to be mostly rust from the corroded tank top, rather than anything of human origin. I had to cut the top off my tanks to get inside, but if you have an inspection hatch there may be no need. I would suggest a good rinsing out - you could use a bilge pump to remove most of the liquid and follow up with a sponge or cloth, then leave the tank open for a while to fully dry out, if you think that is necessary - some clean(ish) water left in there isn't going to do any harm. Edited June 5, 2023 by David Mack Link to comment Share on other sites More sharing options...
Just Heaven Posted June 6, 2023 Report Share Posted June 6, 2023 I replaced ours a while ago, see here : https://www.justheaven.org.uk/2018/08/new-holding-tank/ Link to comment Share on other sites More sharing options...
MrsM Posted June 6, 2023 Report Share Posted June 6, 2023 1 hour ago, Just Heaven said: I replaced ours a while ago, see here : https://www.justheaven.org.uk/2018/08/new-holding-tank/ A really good description of the process. I live in fear of our rank rusting through in places like yours had. Can I ask how old your boat is? M Link to comment Share on other sites More sharing options...
ditchcrawler Posted June 6, 2023 Report Share Posted June 6, 2023 1 hour ago, MrsM said: A really good description of the process. I live in fear of our rank rusting through in places like yours had. Can I ask how old your boat is? M That was a handy miss type 1 1 Link to comment Share on other sites More sharing options...
David Mack Posted June 6, 2023 Report Share Posted June 6, 2023 1 hour ago, MrsM said: A really good description of the process. I live in fear of our rank rusting through in places like yours had. Can I ask how old your boat is? M Mine was about 25 years old when I took it out. The 3mm bottom and lower sides were in almost new condition - no worries about leakage, but the top was like lace, after banging and shoving to remove it loosened the paint and rust. 1 Link to comment Share on other sites More sharing options...
blackrose Posted June 7, 2023 Report Share Posted June 7, 2023 What a horrible situation. I wonder what idiot came up with the idea of mild steel built-in pumpout tanks, especially ones where the boat's baseplate is the bottom of the tank? Link to comment Share on other sites More sharing options...
Tracy D'arth Posted June 7, 2023 Report Share Posted June 7, 2023 3 hours ago, blackrose said: What a horrible situation. I wonder what idiot came up with the idea of mild steel built-in pumpout tanks, especially ones where the boat's baseplate is the bottom of the tank? David Piper for one. The bottom is rarely the problem, its always the top that rots first. I wonder why the builders never realised this and used thicker plate for the top. I doubt that the boat builders 40 and 50 years ago ever thought about their boats lasting as long as many have. Link to comment Share on other sites More sharing options...
Ronaldo47 Posted June 7, 2023 Report Share Posted June 7, 2023 (edited) Never used it on a water tank, but for efficient drying I use an old cylinder vacuum.cleaner that blows as well.as sucks. The hose nozzle can be put in inaccessible places and can blast water droplets out of corners and crevices. Very effective at de-icing the heat exchangers of freezers. The blown air is warm due to having cooled the motor. Edited June 7, 2023 by Ronaldo47 typos Link to comment Share on other sites More sharing options...
Alan de Enfield Posted June 7, 2023 Report Share Posted June 7, 2023 50 minutes ago, Tracy D'arth said: The bottom is rarely the problem, its always the top that rots first. I wonder why the builders never realised this and used thicker plate for the top. Or, even simpler just install the tank upside down. 2 1 Link to comment Share on other sites More sharing options...
system 4-50 Posted June 7, 2023 Report Share Posted June 7, 2023 9 hours ago, Alan de Enfield said: Or, even simpler just install the tank upside down. That won't work. You have to turn it weekly. Link to comment Share on other sites More sharing options...
Just Heaven Posted June 8, 2023 Report Share Posted June 8, 2023 On 06/06/2023 at 10:09, MrsM said: A really good description of the process. I live in fear of our rank rusting through in places like yours had. Can I ask how old your boat is? M The tank was 14 years old when we took it out Steve Link to comment Share on other sites More sharing options...
MrsM Posted June 8, 2023 Report Share Posted June 8, 2023 1 hour ago, Just Heaven said: The tank was 14 years old when we took it out Steve Exactly how old ours is! 😩🤢 Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now