bizzard Posted May 1, 2012 Report Share Posted May 1, 2012 (edited) In days of yore when town gas came on the scene,a great deal of the gas mains run into houses from the street main was made of a lovely metal,''Gunmetal''and possibly other non ferrous metals.The pipework was made up of old rifle barrels from redundant weapons used in all the wars we'd been at.These were all given to hundreds of machine shops all over the place by the ''Gaslight and Coke co''who threaded one end female and tother male so they'd all screw together. Some still in use was discovered quite recently in north London i believe. So that's the way to go with your boats folks.''Gun barrels''it should last at least 200 years. And of course this kind of gas and water pipe is still commonly called ''barrel'',Gas barrel,Water barrel''because of the use of the rifle barrels. Also probably the reason why you see loads of Bayonets in junk shops minus their rifles. BOOM BOOM!!!!!. :closedeyes Edited May 1, 2012 by bizzard Link to comment Share on other sites More sharing options...
ditchcrawler Posted May 1, 2012 Report Share Posted May 1, 2012 I think you'll find it was always measured in cubic feet untill these french utility companies installed metric meters! The meter round my mums old house measures in cubic meters, I read the meter last week. Link to comment Share on other sites More sharing options...
ChrisPy Posted May 1, 2012 Report Share Posted May 1, 2012 The meter round my mums old house measures in cubic meters, I read the meter last week. why do some people adopt the American spelling for metres, when they (the Americans) barely even recognise the existence of such units? It just perpetuates the ignorance and illiteracy of our transatlantic cousins. Link to comment Share on other sites More sharing options...
jonathanA Posted May 1, 2012 Report Share Posted May 1, 2012 Even though it is compressed air pipe that will happily handle 200psi? What's gas pressure - 8psi? Alex 8 PSI - no where near that much -typical propane pressures are 37-50 MilliBars (thousandths of a bar) AFTER the regulator. so 8PSI would be approx 500 milliBar. Are they really, never noticed. They all seem to fit metric tube. - no they don't the 15 x 1/2" BSP connectors fit the taps to the pipe ! you're standard (metric)compression joint wouldn't dirty itself by going anywhere near a tap ! I'm afriad it beats me why 10mm and 15mm copper pipe is perfectly fine for gas (Natural and LPG) everywhere else except a boat.... Link to comment Share on other sites More sharing options...
jckm2000 Posted May 1, 2012 Report Share Posted May 1, 2012 I can't see, in the BSS guide, where it gives a BS number for copper pipe, it just says: "LPG pipework must be made or either seamless copper tube, or stainless steel tube, or copper nickel alloy" The LPG section mentions BS numbers for flexible pipe but none that I can see for copper. I notice the same in the electrical section, no mention of single strand wiring being not allowed in a 240v system, just a requirement that all wire is correctly sized and protected. Very confusing. C. Link to comment Share on other sites More sharing options...
steelaway Posted May 1, 2012 Report Share Posted May 1, 2012 8 PSI - no where near that much -typical propane pressures are 37-50 MilliBars (thousandths of a bar) AFTER the regulator. so 8PSI would be approx 500 milliBar. Are they really, never noticed. They all seem to fit metric tube. - no they don't the 15 x 1/2" BSP connectors fit the taps to the pipe ! you're standard (metric)compression joint wouldn't dirty itself by going anywhere near a tap ! I'm afriad it beats me why 10mm and 15mm copper pipe is perfectly fine for gas (Natural and LPG) everywhere else except a boat.... I knew gas pressure was very low but hadn't realised it was so low - make the point even more. Why are people recommending 15mm pipe when the hole in the hose connection at the gas regulator is less than 5mm? Most modern boats I have seen all seem to be piped in 8-10mm (or imperial equivalent) seamless copper tube with compression fittings, it now seems they are all not to standard Alex What's this if not an adaptor? Link to comment Share on other sites More sharing options...
the grinch Posted May 1, 2012 Report Share Posted May 1, 2012 simple, pressure loss through the pipework must be kept within acceptable drops as for 15mm pipe yes it can be used but must have a thickness of 1.5mm for ANY diameter over 12mm AS I POSTED previously!! Link to comment Share on other sites More sharing options...
ChrisPy Posted May 1, 2012 Report Share Posted May 1, 2012 (edited) I can't see, in the BSS guide, where it gives a BS number for copper pipe, it just says: "LPG pipework must be made or either seamless copper tube, or stainless steel tube, or copper nickel alloy" The LPG section mentions BS numbers for flexible pipe but none that I can see for copper. I notice the same in the electrical section, no mention of single strand wiring being not allowed in a 240v system, just a requirement that all wire is correctly sized and protected. Very confusing. C. these requirements derive from the ISO/BSS standards that are prescribed for the RCD and represent good practice even if there is no requirement to produce an RCD DOC for the boat. However all new boats sold on within 5 years (i.e. all commercially produced boats and most DIY fit-outs) must be issued with an RCD DOC. Edited May 1, 2012 by ChrisPy Link to comment Share on other sites More sharing options...
bizzard Posted May 1, 2012 Report Share Posted May 1, 2012 Whats wrong with rifle barrels.They're not even mentioned in the gas section of the BSS rules,too many joints i expect or something daft like that. Link to comment Share on other sites More sharing options...
Timleech Posted May 1, 2012 Report Share Posted May 1, 2012 Whats wrong with rifle barrels.They're not even mentioned in the gas section of the BSS rules,too many joints i expect or something daft like that. iron pipe is strictly verboten. Tim Link to comment Share on other sites More sharing options...
bizzard Posted May 1, 2012 Report Share Posted May 1, 2012 (edited) iron pipe is strictly verboten. Tim We're not talking muskets Tim. Surely Martini-Henry or Lee-Enfield had gunmetal or hard brass barrels. .303 is a good size for gas pipe and nice and thick too,also the rifling might help to speed the gas on its way albeit in twisted fashion like a Tornado or Barley sugar stick. And i wonder what happened to all the sawn off shotgun barrels. Edited May 1, 2012 by bizzard Link to comment Share on other sites More sharing options...
ditchcrawler Posted May 1, 2012 Report Share Posted May 1, 2012 Whats wrong with rifle barrels.They're not even mentioned in the gas section of the BSS rules,too many joints i expect or something daft like that. Demascus ? Link to comment Share on other sites More sharing options...
bizzard Posted May 1, 2012 Report Share Posted May 1, 2012 Demascus ? Damascus? Did they have rifles and gas cookers in biblical times. Link to comment Share on other sites More sharing options...
Timleech Posted May 1, 2012 Report Share Posted May 1, 2012 We're not talking muskets Tim. Surely Martini-Henry or Lee-Enfield had gunmetal or hard brass barrels. .303 is a good size for gas pipe and nice and thick too,also the rifling might help to speed the gas on its way albeit in twisted fashion like a Tornado or Barley sugar stick. And i wonder what happened to all the sawn off shotgun barrels. I no nerthing about guns, but I'd be surprised to find they have yellow metal barrels. Anyway brass can do funny things with LPG if it's the wrong grade. Link to comment Share on other sites More sharing options...
ditchcrawler Posted May 1, 2012 Report Share Posted May 1, 2012 Damascus? Did they have rifles and gas cookers in biblical times. http://www.google.co.uk/search?q=damascus+steel&ie=UTF-8&oe=UTF-8&hl=en&client=safari Link to comment Share on other sites More sharing options...
Timleech Posted May 1, 2012 Report Share Posted May 1, 2012 Damascus? Did they have rifles and gas cookers in biblical times. Damascus twist barrels. Try googling them. Tim Link to comment Share on other sites More sharing options...
MtB Posted May 1, 2012 Report Share Posted May 1, 2012 I can't see, in the BSS guide, where it gives a BS number for copper pipe, it just says: "LPG pipework must be made or either seamless copper tube, or stainless steel tube, or copper nickel alloy" The LPG section mentions BS numbers for flexible pipe but none that I can see for copper. I notice the same in the electrical section, no mention of single strand wiring being not allowed in a 240v system, just a requirement that all wire is correctly sized and protected. Very confusing. C. You overlooked the bit in the BSS where it says that gas installation must also comply with PD 5482-2005 Part III then. Hope that helps Mike Link to comment Share on other sites More sharing options...
bizzard Posted May 1, 2012 Report Share Posted May 1, 2012 I no nerthing about guns, but I'd be surprised to find they have yellow metal barrels. Anyway brass can do funny things with LPG if it's the wrong grade. Nor do i,but the story in my post about rifle barrel town gas pipes is true,but coal gas of course. http://www.google.co.uk/search?q=damascus+steel&ie=UTF-8&oe=UTF-8&hl=en&client=safari This suits the bayonet rather than the rifle.Interesting though. Link to comment Share on other sites More sharing options...
jckm2000 Posted May 1, 2012 Report Share Posted May 1, 2012 You overlooked the bit in the BSS where it says that gas installation must also comply with PD 5482-2005 Part III then. Hope that helps Mike As a guide to boat owners it's pretty useless then, when to get hold of that PD 54... is over £150. C. Link to comment Share on other sites More sharing options...
bizzard Posted May 1, 2012 Report Share Posted May 1, 2012 Damascus twist barrels. Try googling them. Tim Interesting,laminating strips of metal around a mandrel,I suppose this was before they could machine bore a barrel accurately. I remember seeing a canon barrel made like this somewhere. Link to comment Share on other sites More sharing options...
MoominPapa Posted May 1, 2012 Report Share Posted May 1, 2012 Interesting,laminating strips of metal around a mandrel,I suppose this was before they could machine bore a barrel accurately. I remember seeing a canon barrel made like this somewhere. Mons Meg, in Edinburgh Castle? MP. Link to comment Share on other sites More sharing options...
ditchcrawler Posted May 1, 2012 Report Share Posted May 1, 2012 (edited) Interesting,laminating strips of metal around a mandrel,I suppose this was before they could machine bore a barrel accurately. I remember seeing a canon barrel made like this somewhere. You get a very nicely patterned barrel normaly a rich brown. Old shotguns give a very good example. I think it was also for strength verses weight. Check out this video on YouTube: Brian Holt Edited May 1, 2012 by ditchcrawler Link to comment Share on other sites More sharing options...
bizzard Posted May 1, 2012 Report Share Posted May 1, 2012 Mons Meg, in Edinburgh Castle? MP. That's the one,i've seen it on telly. A steam loco was named Mons Meg too. Link to comment Share on other sites More sharing options...
londonron Posted May 1, 2012 Report Share Posted May 1, 2012 so do we have an answer to this? seems we have gone off topic in a few areas. so if we leave "should you" to another post could we finalise what is legal to do? i am about to install gas piping and was reading this to find out if i should get 8 or 10 mill coils of pipe to supply my oven. im now very confused with all this imperial talk. Link to comment Share on other sites More sharing options...
bizzard Posted May 1, 2012 Report Share Posted May 1, 2012 so do we have an answer to this? seems we have gone off topic in a few areas. so if we leave "should you" to another post could we finalise what is legal to do? i am about to install gas piping and was reading this to find out if i should get 8 or 10 mill coils of pipe to supply my oven. im now very confused with all this imperial talk. Whichever you use make sure its thick wall seamless solid drawn annealed copper tube if using compression fittings because if thin wall is used you will find that the olives will squeeze the tube and you won't get them satisfyingly tight and will probably leak. I think you can get metal inserts to reinforce the tube ends to prevent this happening on thin wall tubing,but it defeats the object by reducing the internal bore size a little. I hasten to add that i am not a registered gas expert but have done a lot of it. Howsat.Please don't go off topic anymore. Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now