Jump to content

Featured Posts

Posted

hi .all. can any one help i thought my water pump had broke ,so i put a new one on .and still no water coming though the taps .the new pump i put on  shurflo 2095/403/443. 28usgpm what ever that means  pressure settings 30 psi any ideas please i would be very grateful thanks

Posted
1 minute ago, haza said:

hi .all. can any one help i thought my water pump had broke ,so i put a new one on .and still no water coming though the taps .the new pump i put on  shurflo 2095/403/443. 28usgpm what ever that means  pressure settings 30 psi any ideas please i would be very grateful thanks

 

Is the pump running ? (electrics getting thru ?)

Is there water in your tank ?

Is the stop-tap open ?

Did you remove any 'end plugs' when connecting the pipes ?

 

28USGPM = 28 US gallons flow per minute (A US gallon is smaller than the UK gallon due to barrel shrinkage) 28 USG = 23 Imperial (UK) gallons.

Posted

Is the pump running when switched on? If not it is not getting power. Fuse? Circuit breaker? wiring?  Time to get the meter out and see if there is any volts.

Posted
2 minutes ago, Ex Brummie said:

If you get it running, I hope you have a large water tank.

 

The manufacturer quotes 10.6Lpm, but it gets a little wearing when you are criticised for correcting posts or providing unasked for information - just 'go with the flow' (see what I did there) and answer the question asked without suplementary information.

 

I'm sure the OP misread 2.8USGPM as 28USGPM

Posted

the pump use to kick in when the taps were in use .the new one kicked  in at first but for some reason it dont now 

2.8 sorry 

Posted
1 minute ago, haza said:

the pump use to kick in when the taps were in use .the new one kicked  in at first but for some reason it dont now 

 

Is it running - electrical wirring noises ?

Have you blown a fuse ?

Can you check ?

Posted

it was running but for some reason its not now .looks like i will have to get some one in .silly question were would i find the fuse thanks any way 

Posted
7 minutes ago, haza said:

silly question were would i find the fuse thanks any way 

 

It could be an inline fuse close to the pump, just follow the wiring as far as you can.

It could be a fuse or an MCB on your electrical panel / "fuse box"

 

Do you have a list of switches marked up "pump". "bilge pump", "tunnel light" etc - they might be 'fused' switches, do they have red lights alongside the switches ?

 

There are so many possibilities that photos of you panel would help.

 

 

Posted

 thanks alan yes i have 12 volt panel with all the info one there the water pressure fuse says 34-15 amp .i would send photos but my phone wont send sorry 

Posted
3 minutes ago, haza said:

 thanks alan yes i have 12 volt panel with all the info one there the water pressure fuse says 34-15 amp .i would send photos but my phone wont send sorry 

 

And can you test the fuse ?

Do you have a multimeter ?

 

Is so, set it to the Ohm** scale, touch the two probes together and note the reading, now touch each end of the fuse (one probe on each end) and see it the reading is the same, if it is that means the fuse is OK (not blown).

 

** set the dial to the highest number (maybe 2000 ?) on the scale that show this symbol Ω

 

If you get a no reading or "OL" then the fuse is blown and needs replacing.

 

If the fuse blows again you have a wiring problem, or have replaced the pump with one that requires thicker wiring / bigger fuse. DO NOT just replace the old fuse with a bigger one. Find the problem first.

Posted

A good first check would be to remove the fuse and push it back in again. Sometimes the contacts for the fuse can get corroded and interrupt supply. removing and refitting the fuse can clean the tarnish off.

Jen

Posted

thanks all .its all to much for me i will get a guy called ian in from out of nantwhich thats if i can find is number hes the guy who does my boat safety as any one got is number  sorry for being so vague with this .thanks any way 

Posted

If you are in the West Midlands, you don’t need to get someone from Cheshire in. Whereabouts are you, I may be able to suggest someone local.

Posted
3 minutes ago, MPR said:

Dave Freeman Taft Wharf Wolseley Bridge 07918 677782 must be even nearer you

I thought Cannock  was off the Curley Whirly 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.