mboat01 Posted February 20, 2019 Report Share Posted February 20, 2019 Complete boat refit - going to run wiring boxed in under gunwales (12v on one side, 230v on another). At one point this will mean the wiring running behind the stove (this will be tiled and stove insulation boarded to BS8511). Is this : (a) Safe generally ? - is there a risk of plastic round wires melting ??, and; (b) Ok in terms of BSS ?. Link to comment Share on other sites More sharing options...
Johny London Posted February 20, 2019 Report Share Posted February 20, 2019 When I did the surround for my stove, I cut out the wall ply and replaced it with Cal-sil board (to maximise space) and there were a couple of wires in the void. I made sure they were well secured away from the back of the cal-sil board. So, to try and help with your question, I think the devil is in the detail. The cal-sil board is very very good at stopping heat transfer - I've got a bit just sitting on the side by the stove that I haven't finished yet so I can access behind it (the washing machine!) and it never gets hot or even barely warm in there. If you have cal-sil board, and a decent sized space for the wires, and they are clipped more to the side away from the board, in my opinion you should be very ok. (you wouldn't want the wires getting any more than very slightly warm-ish because eventually they could degrade) You could always stick a temperature probe in for a couple weeks, just to check what goes on in there. This is the thing with nb's - one thing runs into another. Link to comment Share on other sites More sharing options...
Rob-M Posted February 20, 2019 Report Share Posted February 20, 2019 Our oven has electric running to it for the ignitor, obviously that wiring runs to the cooker and I presume that is ok without any protection other than what the cooker manufacturer has put on the back of the unit. Link to comment Share on other sites More sharing options...
Alan de Enfield Posted February 20, 2019 Report Share Posted February 20, 2019 34 minutes ago, Sassy Lass said: At one point this will mean the wiring running behind the stove Solid Fuel Stove or Gas cooker ? I think you have had answers covering both options. Link to comment Share on other sites More sharing options...
Chewbacka Posted February 20, 2019 Report Share Posted February 20, 2019 Good heat insulation between the cables and stove and an air gap between the back of the insulation board and the cable. Not sure what cable you are using but arctic cable is usually rated up to 60c or higher. So a well installed stove installation should not be that hot behind the insulation board. Link to comment Share on other sites More sharing options...
mboat01 Posted February 20, 2019 Author Report Share Posted February 20, 2019 Thanks All. It will be a morso 1410 with min 45mm gap to tiles, 25mm silicate board, 10mm airgap (as per http://www.soliftec.com/Boat Stoves 1-page.pdf) to the side walls. I'll line bottom of wire tray under gunwales behind stove with a base of 25mm silicate. If arctic cable has inc temp rating then I guess thats another reason to use it... pity about price !!! -- know any good suppliers ?? Link to comment Share on other sites More sharing options...
Chewbacka Posted February 20, 2019 Report Share Posted February 20, 2019 1 hour ago, Sassy Lass said: Thanks All. It will be a morso 1410 with min 45mm gap to tiles, 25mm silicate board, 10mm airgap (as per http://www.soliftec.com/Boat Stoves 1-page.pdf) to the side walls. I'll line bottom of wire tray under gunwales behind stove with a base of 25mm silicate. If arctic cable has inc temp rating then I guess thats another reason to use it... pity about price !!! -- know any good suppliers ?? Toolstation do you? https://www.toolstation.com/arctic-pvc-cable-3183a/p24117 Link to comment Share on other sites More sharing options...
Boater Sam Posted February 21, 2019 Report Share Posted February 21, 2019 2.5mm immersion heater flex is high temperature pvc insulation, better than arctic cable. But if you have the cable against the hull steel it won't get hot anyway. Link to comment Share on other sites More sharing options...
Johny London Posted February 26, 2019 Report Share Posted February 26, 2019 Yes that's true the hull we be an excellent heat sink! Link to comment Share on other sites More sharing options...
mboat01 Posted February 26, 2019 Author Report Share Posted February 26, 2019 (edited) humm ... good idea ...I could scrape away foam to hull, get some high temp adhesive (- do you think this would be ok ?), bond this to hull and cables through Edited February 26, 2019 by Sassy Lass Link to comment Share on other sites More sharing options...
ditchcrawler Posted February 26, 2019 Report Share Posted February 26, 2019 I would be very concerned if the temperature behind the lining was hot enough to damage a cables insulation, I think I might have other things to worry about Link to comment Share on other sites More sharing options...
mboat01 Posted February 26, 2019 Author Report Share Posted February 26, 2019 yes ! ... my concern is really about temps around say 100deg over many months/years degrading cable plastic, shorting out and it being a real pita to sort out, ie., needing tiling etc behind stove to be removed Link to comment Share on other sites More sharing options...
WotEver Posted February 26, 2019 Report Share Posted February 26, 2019 Just now, Sassy Lass said: yes ! ... my concern is really about temps around say 100deg over many months/years degrading cable plastic, shorting out and it being a real pita to sort out, ie., needing tiling etc behind stove to be removed If you’ve got temps above 100C behind the lining then you’ve made a real mess of installing the stove surround. It should be barely above ambient if done correctly. Link to comment Share on other sites More sharing options...
mboat01 Posted February 26, 2019 Author Report Share Posted February 26, 2019 thanks.... looks like its not a prob !. good news ?? Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now