Traveller Posted November 28, 2014 Report Share Posted November 28, 2014 Whilst working ok the Water Temp Control Knob has seized and I cannot therefore turn up or down the water temperature. Can anybody offer any pointers on how to fix this or is it Paloma are out of production so get a newer model :-( Link to comment Share on other sites More sharing options...
Paloma Bob Posted November 28, 2014 Report Share Posted November 28, 2014 Hi there, Which model Paloma do you have ? Regards Bob Link to comment Share on other sites More sharing options...
Traveller Posted November 28, 2014 Author Report Share Posted November 28, 2014 (edited) PH5-3F, I believe but I am not on the boat at the mo. The pic I found on Google looks identical though. Colin Edited November 28, 2014 by Traveller Link to comment Share on other sites More sharing options...
springy Posted November 28, 2014 Report Share Posted November 28, 2014 It seems to be lack of use as a temperature adjuster which causes this - mine has done it a few times over the years - my solution - remove the control knobs and cover and then using a small adjustable spanner or pliers on the shaft gently work the adjuster back and forth until it is all free, dont use the knob - it doesn't feel strong enough. I have done this at least 4 times over the past 10-12 years (usually when re-commisioning after the winter draindown) and it has always worked ok. maybe a monthly adjustment to the temp control would prevent this ? springy Link to comment Share on other sites More sharing options...
Traveller Posted November 28, 2014 Author Report Share Posted November 28, 2014 Thanks Springy, sounds like a plan to me :-) Link to comment Share on other sites More sharing options...
J R ALSOP Posted November 28, 2014 Report Share Posted November 28, 2014 I spend half my life freeing these of, as Springy says, "that's the way to do it". Link to comment Share on other sites More sharing options...
MtB Posted November 28, 2014 Report Share Posted November 28, 2014 Thirded! MtB Link to comment Share on other sites More sharing options...
Wanted Posted November 28, 2014 Report Share Posted November 28, 2014 Forthded... Also, Can I just add that Paloma Bob is a valuable resource for Paloma owning boaters. I have one of his recons and the service was amazing. Cracking stuff! 1 Link to comment Share on other sites More sharing options...
Traveller Posted November 28, 2014 Author Report Share Posted November 28, 2014 (edited) Thanks everybody for your input. I will certainly remember Paloma Bill and the service he provides. Edited November 28, 2014 by Traveller Link to comment Share on other sites More sharing options...
Paloma Bob Posted November 29, 2014 Report Share Posted November 29, 2014 Try what has already been suggested and if that fails, or you wring off the shaft then get back to me and I'll tell you what you can try next. P.S. I spend all my life freeing these :-( Link to comment Share on other sites More sharing options...
MtB Posted November 29, 2014 Report Share Posted November 29, 2014 Thanks everybody for your input. I will certainly remember Paloma Bill and the service he provides. And if Paloma Bill lets you down, try Paloma Bob!! MtB Link to comment Share on other sites More sharing options...
hilaryb Posted November 29, 2014 Report Share Posted November 29, 2014 Personnelly i wont even try....ebay part ex £125...send yours get recon back easy peasey Link to comment Share on other sites More sharing options...
DeanS Posted November 29, 2014 Report Share Posted November 29, 2014 Personnelly i wont even try....ebay part ex £125...send yours get recon back easy peasey glad you have £125 lying around to blow ;-) Link to comment Share on other sites More sharing options...
Traveller Posted December 1, 2014 Author Report Share Posted December 1, 2014 (edited) Tried easing with a a grip (after removing plastic knob) but it really is locked solid and I could not get it to move :-( Any further suggestions? Edited December 1, 2014 by Traveller Link to comment Share on other sites More sharing options...
Wanted Posted December 1, 2014 Report Share Posted December 1, 2014 Give Bob a shout Link to comment Share on other sites More sharing options...
J R ALSOP Posted December 1, 2014 Report Share Posted December 1, 2014 Try harder. Link to comment Share on other sites More sharing options...
Traveller Posted December 1, 2014 Author Report Share Posted December 1, 2014 (edited) Got as far as using mole grips - if I'd tried any harder the heater would have come of the wall or the spindle would have snapped. I'll drop a pm to Paloma Bob. Edited December 1, 2014 by Traveller Link to comment Share on other sites More sharing options...
springy Posted December 1, 2014 Report Share Posted December 1, 2014 Its just that fine balance between freeing it and breaking it - I tried to move mine yesterday - its stuck !! springy Link to comment Share on other sites More sharing options...
Alan Saunders Posted December 1, 2014 Report Share Posted December 1, 2014 Freeing siezed valves and screws is a fine art. Brute force and ignorance may succeed but a little finesse and patience will provide a permanent repair. Aternately apply gentle tightening and loosening pressure. There may initially be no perceptible movement. Gas taps can usually be dismantled, cleaned (maybe lapped in) and lubricated with a suitable grease. Alan Link to comment Share on other sites More sharing options...
Batavia Posted December 2, 2014 Report Share Posted December 2, 2014 Got as far as using mole grips - if I'd tried any harder the heater would have come of the wall or the spindle would have snapped. I'll drop a pm to Paloma Bob. An alternative approach is to remove the plate which holds the rotating part of the valve in place and then to pull the valve out, without twisting. You are much less likely to break the spindle when it is in tension as opposed to torsion. This has worked for me on a couple of occasions. PS It is a good idea to drain the water heater before starting to do this! Chris G Link to comment Share on other sites More sharing options...
John_G Posted February 21, 2020 Report Share Posted February 21, 2020 On 02/12/2014 at 17:05, Batavia said: An alternative approach is to remove the plate which holds the rotating part of the valve in place and then to pull the valve out, without twisting. You are much less likely to break the spindle when it is in tension as opposed to torsion. This has worked for me on a couple of occasions. PS It is a good idea to drain the water heater before starting to do this! Chris G Hi I have a stuck temperature adjuster, tried WD-40, penetrating oil and heat and it will not free up. I did manage to pull the splined shaft out of the valve. Can the valve bodyt be tapped out? Looking at the photo, the pencil is pushed into the inlet pipe as far as it can go. Is the pencil resting onto the rear face of the temperature adjuster valve or is touching up against an internal wall in the valve? Any help much appreciated. John_G Link to comment Share on other sites More sharing options...
John_G Posted February 22, 2020 Report Share Posted February 22, 2020 22 hours ago, John_G said: Hi I have a stuck temperature adjuster, tried WD-40, penetrating oil and heat and it will not free up. I did manage to pull the splined shaft out of the valve. Can the valve bodyt be tapped out? Looking at the photo, the pencil is pushed into the inlet pipe as far as it can go. Is the pencil resting onto the rear face of the temperature adjuster valve or is touching up against an internal wall in the valve? Any help much appreciated. John_G Hi I worked it out, and the shaft can be driven out with a drift replacing the pencil position. Happy to now have a cleaned and fully working temperature valve. John_G 1 Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now