Matthew Knowles Posted July 13, 2009 Report Share Posted July 13, 2009 We have a rear hatch that currently run steel against steel making it quite hard to open/close and impossible to do so quietly. I notice that most boats seem to have thin steel strips both on the hatch and on the boat. Where would I source these from and how would I attach it (adhesive?). Many thanks, Matt Link to comment Share on other sites More sharing options...
wrigglefingers Posted July 13, 2009 Report Share Posted July 13, 2009 We have a rear hatch that currently run steel against steel making it quite hard to open/close and impossible to do so quietly. I notice that most boats seem to have thin steel strips both on the hatch and on the boat. Where would I source these from and how would I attach it (adhesive?). Many thanks, Matt Sometimes candle wax and a polish helps ....... Link to comment Share on other sites More sharing options...
Martin Kedian Posted July 13, 2009 Report Share Posted July 13, 2009 (edited) Sometimes candle wax and a polish helps ....... Most boats run on brass strips often drilled and tapped into the angle runners with countersunk screws another alternative is brass blocks with a slot in that are fixed to the hatch these fit over the outside edge of the angle which in turn has a brass chanel fitted over it I hope this helps you can by brass flat bar from B and Q Regards Martin Edited July 13, 2009 by Martin Kedian Link to comment Share on other sites More sharing options...
WotEver Posted July 13, 2009 Report Share Posted July 13, 2009 Sometimes candle wax and a polish helps ....... Another (unusual) alternative in the last paragraph here: http://tuglyranarrowboatcharles.blogspot.c...-and-hatch.html T. Link to comment Share on other sites More sharing options...
Matthew Knowles Posted July 13, 2009 Author Report Share Posted July 13, 2009 Another (unusual) alternative in the last paragraph here:http://tuglyranarrowboatcharles.blogspot.c...-and-hatch.html T. If fitted with those you could have fun trying to close the hatch by accelerating and open the hatch by stopping quickly. I'm very good at the latter, usually with the help of lock gates, banks, other craft, walls, etc. Link to comment Share on other sites More sharing options...
carlt Posted July 13, 2009 Report Share Posted July 13, 2009 Another (unusual) alternative in the last paragraph here:http://tuglyranarrowboatcharles.blogspot.c...-and-hatch.html T. It would be interesting to hear how this idea is performing, after 3 years. Link to comment Share on other sites More sharing options...
WotEver Posted July 13, 2009 Report Share Posted July 13, 2009 It would be interesting to hear how this idea is performing, after 3 years. I was wondering the same thing. Those runners are only thin steel - wouldn't they have rusted through by now? Link to comment Share on other sites More sharing options...
churchward Posted July 13, 2009 Report Share Posted July 13, 2009 (edited) Many rear hatches use brass strips and bearings of some kind. Brass on brass is "slippery" as the metal doesn't grab itself (like mild steel does) but with frequent use will burnish. Chandlers sell such things. the runner strips can be screwed or pot riveted to the boat both would need to be counter suck of course. See here for two slightly different options for brass hatch runners. http://www.midlandchandlers.co.uk/HATCH-RUNNERS_B215D5.aspx They don't have pics of them but it will give you an idea of cost. One type uses a "C" section brass length that fits to the edge of the boats raised section for the hatch runway and the brass bearings attach to the hatch and run along either side of the edge. The other method uses a flat brass strip on top of the boats raised hatch runway section and the bearings run along the top of this but also go under neat the runway so that the hatch can't be lifted off. In choosing it is a case of deciding if the hatch is wide enough to fit the edge "c" section method or not. Edited July 13, 2009 by churchward Link to comment Share on other sites More sharing options...
charles123 Posted July 13, 2009 Report Share Posted July 13, 2009 It would be interesting to hear how this idea is performing, after 3 years. Fine Carl, working just fine, the rear hatch runners are a form of very hard plastic that I got from Puffer Parts chandlers, one less thing to polish I thought, however next time I would chose brass runners, the front are the same however I used the wheels as described on the blog, no problem, the do run freely but the weight of the hatch means you have to push it open and closed, you cant give it a push and let it run itself to the stops BTW its for sale on the duck! Charles Link to comment Share on other sites More sharing options...
Hawksey Posted July 13, 2009 Report Share Posted July 13, 2009 We have a rear hatch that currently run steel against steel making it quite hard to open/close and impossible to do so quietly. I notice that most boats seem to have thin steel strips both on the hatch and on the boat. Where would I source these from and how would I attach it (adhesive?). Many thanks, Matt I had the same problem. Got some 1mm Tufnol cut into 25mm strips and stuck to the existing steel runners on the boat and hatch. Slides much better now. http://www.directplasticsonline.co.uk/ . Link to comment Share on other sites More sharing options...
WotEver Posted July 13, 2009 Report Share Posted July 13, 2009 I had the same problem.Got some 1mm Tufnol cut into 25mm strips and stuck to the existing steel runners on the boat and hatch. Slides much better now. How did you attach it? Will it glue? T. Link to comment Share on other sites More sharing options...
ayeaye Posted July 13, 2009 Report Share Posted July 13, 2009 How did you attach it? Will it glue? T. We got some very hard rubber runners from "Puffer Parts" working fine 3 years later had to drill and screw them on Bren Link to comment Share on other sites More sharing options...
Hawksey Posted July 13, 2009 Report Share Posted July 13, 2009 How did you attach it? Will it glue? T. I glued it on with the recommend Bostik 2402. Seems to be holding up well so far (just over a year). . Link to comment Share on other sites More sharing options...
ThePiglet Posted July 13, 2009 Report Share Posted July 13, 2009 (edited) I was planning on using brass strips on my visuble runners with PTFE strips on the underside of the hatch. Both held with countersunk bolts. Edited July 13, 2009 by ThePiglet Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now