real_vibes Posted September 11, 2013 Report Share Posted September 11, 2013 What's best? Lots of areosol stuff on eBay, I am leaning towards the pita of stuff on eBay though. What is best. It's a squirrel. Mainly asking as the joint between the stove and the chimney is looking a little sad for itself and starting to look rusty. Link to comment Share on other sites More sharing options...
Mike Tee Posted September 11, 2013 Report Share Posted September 11, 2013 (edited) rub down with fine wet and dry, then try this stuff http://www.thefiresideshop.co.uk/stove-grate-polish-170gm.html#.UjDZBj9h-No eta - not particularly from these people, it was the first one that came up on search Edited September 11, 2013 by Mike Tee Link to comment Share on other sites More sharing options...
Grace and Favour Posted September 11, 2013 Report Share Posted September 11, 2013 I would suggest that a tin of (the appropriate) brushing paint is better than a spray can. You get more for your £ It's easier to use It won't cover your boat in overspray Link to comment Share on other sites More sharing options...
Pykebird Posted September 12, 2013 Report Share Posted September 12, 2013 I have just done my squirrel in spary paint from wilckos. It was around £6 a can and although I got 2 I only used a small amount out of one, I also did the chimney in and out around 3 coats.I used sand paper to rub any loose rust off first. IF I can use a spray can, anyone can, I just put an old sheet up behind, so the cream walls did not get sprayed and went from side to side. I lit it for the first time yesterday, no fumes and no smell. Link to comment Share on other sites More sharing options...
bizzard Posted September 12, 2013 Report Share Posted September 12, 2013 You can spray the stove paint from an aerosol into its cap or a pot and brush it on. Link to comment Share on other sites More sharing options...
Phil Ambrose Posted September 12, 2013 Report Share Posted September 12, 2013 I black lead and polish, works for me. You can do it at anytime without having to prep up and just do the area in need. Phil Link to comment Share on other sites More sharing options...
Chick-Chick-Chicken Posted September 12, 2013 Report Share Posted September 12, 2013 I'd go with the grate polish too, much easier. If you've not done it before, make sure you light a small fire when it's done and be ready to open all doors. Link to comment Share on other sites More sharing options...
Sir Nibble Posted September 12, 2013 Report Share Posted September 12, 2013 Contact oilstoves and get a tin of pukka morso paint. Link to comment Share on other sites More sharing options...
GUMPY Posted September 17, 2013 Report Share Posted September 17, 2013 I use everbuild heat resistant paint on my flue and stove. You will need the doors and windows when painting and on first firing. http://www.ebay.co.uk/itm/200696991293 Link to comment Share on other sites More sharing options...
Chertsey Posted September 17, 2013 Report Share Posted September 17, 2013 Another vote for using polish/stove black. Liberon iron paste is the best stuff if you can find it (and thanks again to Speedwheel for putting us onto it). If the joint is looking iffy seal it all up neatly with some high temp silicone (the red stuff) and then black polish over it. So much easier, longer lasting and better looking than fire cement and paint. Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now