curzons246 Posted December 26, 2007 Report Share Posted December 26, 2007 I've just been watching narrow boat afloat - they show a boat hitched to the lock gate - the boat reverses pulls open the gate, sails through and the rope falls from the gate - all the captin gives away is that when pulled its a hitch and when the boat passes through it's no longer a hitch and so can be collected without having to untie it - can any one share the knowledge with me please? Link to comment Share on other sites More sharing options...
magnetman Posted December 26, 2007 Report Share Posted December 26, 2007 (edited) Its called 'thumblining' Edited December 26, 2007 by magnetman Link to comment Share on other sites More sharing options...
Supermalc Posted December 26, 2007 Report Share Posted December 26, 2007 http://www.canalworld.net/forums/index.php...;hl=thumblining Link to comment Share on other sites More sharing options...
owen Posted December 29, 2007 Report Share Posted December 29, 2007 http://www.canalworld.net/forums/index.php...;hl=thumblining hey malc do you know wether horses are allowed on the tow path to pull boats Link to comment Share on other sites More sharing options...
rrt2 Posted January 8, 2008 Report Share Posted January 8, 2008 Its not a knot but you trap one end of the line so that when you reverse the line from the towing mast traps the line and pulls the gate open and when it goes slack as you exit the lock it all comes loose and the line pulls away with you. The gate rails on the the G.U. were or still are shaped the way they are for this reason. Link to comment Share on other sites More sharing options...
David Schweizer Posted January 8, 2008 Report Share Posted January 8, 2008 (edited) Its not a knot but you trap one end of the line so that when you reverse the line from the towing mast traps the line and pulls the gate open and when it goes slack as you exit the lock it all comes loose and the line pulls away with you. The gate rails on the the G.U. were or still are shaped the way they are for this reason. Welome to the Forum Barry. The practice of placing swan neck shaped rails on the bottom gates was not univesal, for example several locks on the Braunston flight did not have tham. It was still possible to thumbline on them but you had to wait until the water level had dropped a bit, and it sometimes needed two people to stop the line from slipping over the top of the rail. I am, sure if we ask nicely Alan Fincher will dig out some old photos of it being done on straight siderd rails. Edited January 8, 2008 by David Schweizer Link to comment Share on other sites More sharing options...
Hairy-Neil Posted January 8, 2008 Report Share Posted January 8, 2008 Welome to the Forum Barry. The practice of placing swan neck shaped rails on the bottom gates was not univesal, for example several locks on the Braunston flight did not have tham. It was still possible to thumbline on them but you had to wait until the water level had dropped a bit, and it sometimes needed two people to stop the line from slipping over the top of the rail. Yes, it works just the same on those type rails too. Never needed the second man in my experience either. A few are now getting hand rails at both sided of the catwalk. These seem to make the procedure somewhat more risky. Link to comment Share on other sites More sharing options...
David Schweizer Posted January 8, 2008 Report Share Posted January 8, 2008 Yes, it works just the same on those type rails too. Never needed the second man in my experience either. A few are now getting hand rails at both sided of the catwalk. These seem to make the procedure somewhat more risky. I agree. In most cases we had no problem especially as we took the thumbline from the front stud rather than the towing post. but some of the bigger Town Class working boats did have to be careful if using thumblining when empty in a shallow lock, as the towing post top could be significantly higher than the hand rail. Link to comment Share on other sites More sharing options...
m589 Posted January 11, 2008 Report Share Posted January 11, 2008 Basically a slip knot pull one way it holds tight, pull the other it goes loose. Thumblining is very simple in principle but it takes some practice to get it right, due to the varying depths of locks. Also nowadays there are lots of odd bolts sticking out from lockgates which can foul the free release of thumblines and one has to be very careful to check the line comes free. Link to comment Share on other sites More sharing options...
Sylver Lining Posted January 17, 2008 Report Share Posted January 17, 2008 Wow. I don't get how to do it, but sounds like a bit of an art. Currently trying to learn how to splice. Link to comment Share on other sites More sharing options...
kingofthecut Posted February 22, 2008 Report Share Posted February 22, 2008 Basically a slip knot pull one way it holds tight, pull the other it goes loose. Thumblining is very simple in principle but it takes some practice to get it right, due to the varying depths of locks. Also nowadays there are lots of odd bolts sticking out from lockgates which can foul the free release of thumblines and one has to be very careful to check the line comes free. Depth of lock is not really an issue because the angle of the line is so flat, usually starts slightly above horizontal and ends slightly below meaning that the difference in the position of the boat is negligable. Plus most locks where it is a common practice are plenty long enough to allow some margin for error. Link to comment Share on other sites More sharing options...
kingofthecut Posted February 22, 2008 Report Share Posted February 22, 2008 (edited) Welome to the Forum Barry. The practice of placing swan neck shaped rails on the bottom gates was not univesal, for example several locks on the Braunston flight did not have tham. It was still possible to thumbline on them but you had to wait until the water level had dropped a bit, and it sometimes needed two people to stop the line from slipping over the top of the rail. I am, sure if we ask nicely Alan Fincher will dig out some old photos of it being done on straight siderd rails. Using two people completely defeats the object!!!! They might as well just open the gate! It is to be used when short handed to negate the need to reverse boat, climb up lock, open gate, take boats out etc. If there are two on the lockside there is no need to bother! Edited February 23, 2008 by kingofthecut Link to comment Share on other sites More sharing options...
bargeeboy Posted February 22, 2008 Report Share Posted February 22, 2008 It way for pure effieciency Once paddles were drawn the lock wheeler would attach lines and cycle off The boatman would open the gates with the boats' thumblines and leave the lock Locks were left with paddles up and gates open. I've got some video somewhere I'll try to sort out I think its Greyhound and Fazeley in the 90's Link to comment Share on other sites More sharing options...
kingofthecut Posted February 23, 2008 Report Share Posted February 23, 2008 (edited) It way for pure effieciencyOnce paddles were drawn the lock wheeler would attach lines and cycle off The boatman would open the gates with the boats' thumblines and leave the lock Locks were left with paddles up and gates open. Agreed, giving those on the tiller a chance to do the range, check the stew, oil the engine etc. without losing anytime while locking. Edited February 23, 2008 by kingofthecut Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now