blackrose Posted February 25, 2022 Report Share Posted February 25, 2022 (edited) I've fitted my new Thetford toilet and christened it this morning. But it's not installed against a bulkhead as that wouldn't have worked in my bathroom. So I need to box in the hose at the back with something 18cm wide and about a foot high and fit the control panel into the top of that. Then also make some sort of n-shaped removable 15cm - 20cm long cover to go over the end of the cassette where it sticks out of the toilet. What's the best material to use? White faced furniture board? Or should I just find a cheap slim bathroom wall cabinet and cut into it? I'm not much of a cabinet maker so a ready built unit that I could modify might be easier. Or any other ideas? Edited February 25, 2022 by blackrose Link to comment Share on other sites More sharing options...
nbfiresprite Posted February 25, 2022 Report Share Posted February 25, 2022 This may do the job https://www.bmstores.co.uk/products/maine-bathroom-storage-unit-355081 Move the base further up, you have some storge space as well Link to comment Share on other sites More sharing options...
matty40s Posted February 25, 2022 Report Share Posted February 25, 2022 You've got a widebeam, why are you struggling to squeeze it in....just asking? Link to comment Share on other sites More sharing options...
blackrose Posted February 25, 2022 Author Report Share Posted February 25, 2022 (edited) 20 minutes ago, matty40s said: You've got a widebeam, why are you struggling to squeeze it in....just asking? I'm not struggling to squeeze it in. I'm just trying to box in some parts. Not sure why you thought I was saying it's a problem with a lack of space? 23 minutes ago, nbfiresprite said: This may do the job https://www.bmstores.co.uk/products/maine-bathroom-storage-unit-355081 Move the base further up, you have some storge space as well Thanks, yes I did see those bathroom storage boxes on Amazon. A couple of those might work Edited February 25, 2022 by blackrose Link to comment Share on other sites More sharing options...
Guest Posted February 26, 2022 Report Share Posted February 26, 2022 Im clearly missing something here but why didnt you fit a c260, up against a fitted bulkhead installed to the left side of the toilet? With a hatch to pull the cassette through? Then rotate the bowl 90 degrees. Link to comment Share on other sites More sharing options...
blackrose Posted February 26, 2022 Author Report Share Posted February 26, 2022 (edited) As I said in my original post, fitting it to a bulkhead isn't possible in my bathroom - at least not without some major refitting. If you're talking about the bulkhead shown to the left of the toilet in my picture, there's a double bed up against the other side of it and I'm not going to move it or crawl under it everytime I want to get the cassette out. If you look carefully maybe you can also see a boxed in area on the floor up against the bulkhead. That contains pipes to/from the corner shower which occupies the perpendicular corridor bulkhead to the left of where the picture was taken from. It's also not possible to use the other bulkhead on the right separating the bathroom from the saloon because there's a big stove and pipework connecting to radiators in the way. I'm not sure how the C260 would have solved any of that? Isn't it essentially the same toilet as my C263 with a higher back cistern type bulkhead fitting? Edited February 26, 2022 by blackrose Link to comment Share on other sites More sharing options...
blackrose Posted February 26, 2022 Author Report Share Posted February 26, 2022 (edited) Here's are a couple of old pictures of the bathroom showing lack of bulkhead availability which might make things clearer. It was originally fitted out nearly 17 years ago with a Vacuflush toilet with remote cassette (the one I've just taken out). That cassette unit was on the other side of the saloon bulkhead but connected to the toilet bowl with a 3m long 38mm ID sanitary waste pipe. Edited February 26, 2022 by blackrose Link to comment Share on other sites More sharing options...
Guest Posted February 26, 2022 Report Share Posted February 26, 2022 (edited) 7 hours ago, blackrose said: As I said in my original post, fitting it to a bulkhead isn't possible in my bathroom - at least not without some major refitting. If you're talking about the bulkhead shown to the left of the toilet in my picture, there's a double bed up against the other side of it and I'm not going to move it or crawl under it everytime I want to get the cassette out. If you look carefully maybe you can also see a boxed in area on the floor up against the bulkhead. That contains pipes to/from the corner shower which occupies the perpendicular corridor bulkhead to the left of where the picture was taken from. It's also not possible to use the other bulkhead on the right separating the bathroom from the saloon because there's a big stove and pipework connecting to radiators in the way. I'm not sure how the C260 would have solved any of that? Isn't it essentially the same toilet as my C263 with a higher back cistern type bulkhead fitting? No I mean you construct a bulkhead specifically to fix the back of the toilet to. With a hatch in in it. The hatch is then opened and the cassette pulled out into the bathroom not on the other side of the bathroom wall/bulkhead. Though maybe the c200 would be better as it's not as tall as the c260. The C260/200 is different from the c263 as the cassette doesn't protrude in the same way. It essentially sits entirely within the casing of the toilet. Meaning you don't have to contend with enclosing the end of the cassette and find somewhere to mount the switch panel.as you are now having to do. The 260/200 is like the 262/263cs - you can compare here. Edited February 26, 2022 by The Happy Nomad Add a better pic. Link to comment Share on other sites More sharing options...
Guest Posted February 26, 2022 Report Share Posted February 26, 2022 As to now hiding stuff perhaps you could now make something from UPVC fascia or wall board?? Link to comment Share on other sites More sharing options...
blackrose Posted February 26, 2022 Author Report Share Posted February 26, 2022 (edited) 1 hour ago, The Happy Nomad said: No I mean you construct a bulkhead specifically to fix the back of the toilet to. With a hatch in in it. The hatch is then opened and the cassette pulled out into the bathroom not on the other side of the bathroom wall/bulkhead. Though maybe the c200 would be better as it's not as tall as the c260. The C260/200 is different from the c263 as the cassette doesn't protrude in the same way. It essentially sits entirely within the casing of the toilet. Meaning you don't have to contend with enclosing the end of the cassette and find somewhere to mount the switch panel.as you are now having to do. The 260/200 is like the 262/263cs - you can compare here. Well I did think of making a bulkhead but in the end I decided that making a simple cover for the end of the cassette is going to be easier than making a bulkhead and more importantly it's also going to be much easier to get the cassette out without having to crawl around the back of a bulkhead. It's been thought through. Edited February 26, 2022 by blackrose Link to comment Share on other sites More sharing options...
Guest Posted February 26, 2022 Report Share Posted February 26, 2022 1 minute ago, blackrose said: Well, I think making a simple cover for the end of the cassette is going to be easier than making a bulkhead and it's also going to be easier to get the cassette out without having to crawl around the back of a bulkhead. If you think I mean you will need to crawl around doing anything then I am afraid you have completely misunderstood what I am describing. But I've tried to explain it as best I can. I have scoured the internet for a picture of what I am talking about but have failed miserably even though I have seen such an arrangement in boats. Link to comment Share on other sites More sharing options...
blackrose Posted February 26, 2022 Author Report Share Posted February 26, 2022 (edited) I think I've understood what you mean, I just don't think there's any need for an extra mini bulkhead and hatch in the bathroom. It's overly complicated in terms of both building it and using it. My idea is much simpler in every way. Edited February 26, 2022 by blackrose Link to comment Share on other sites More sharing options...
Guest Posted February 26, 2022 Report Share Posted February 26, 2022 Finally found a pic. of what I was meaning. But as I said this would only work if you hadn't opted for the C263. Link to comment Share on other sites More sharing options...
blackrose Posted February 26, 2022 Author Report Share Posted February 26, 2022 Yes I see and I had understood, I just don't want to do that. Link to comment Share on other sites More sharing options...
Guest Posted February 26, 2022 Report Share Posted February 26, 2022 Found another. This time a C260 1 minute ago, blackrose said: Yes I see and I had understood, I just don't want to do that. Fair enough then it needs something constructing. But if that white unit next to it is not movable then the cassette will need to come outwards and upwards. Restricting your options. Unless you made something like a 'hood' that could be lifted up and out the way. Link to comment Share on other sites More sharing options...
blackrose Posted February 26, 2022 Author Report Share Posted February 26, 2022 (edited) Yes, I looked at the C260 other Thetford toilets with the higher bulkhead backs but I didn't want one of those. I don't like the look of them and in my case because of my bathroom configuration I'd have to get around the back of the bulkhead to get the cassette out. I don't want a free standing bulkhead in my bathroom like the one in the picture above. I prefer the C263 without the back and no bulkhead in the way. Edited February 26, 2022 by blackrose Link to comment Share on other sites More sharing options...
Guest Posted February 26, 2022 Report Share Posted February 26, 2022 7 minutes ago, blackrose said: . It's overly complicated in terms of both building it and using it. My idea is much simpler in every way. Sorry but I cannot agree. The simple fact is you appear to have bought the wrong toilet for the intended installation. A simple short bulkhead would have been easy to construct compared to what you now need to do. You also need to make something to mount the switch panel. With the correct choice of loo you wouldn't need to that as it's incorporated into the casing. Link to comment Share on other sites More sharing options...
Guest Posted February 26, 2022 Report Share Posted February 26, 2022 30 minutes ago, blackrose said: Ah right so that cabinet does move out the way. This wasn't totally clear earlier. Then you could permanently fit a box/hood over the cassette end that mates up to where the cabinet sits. It would need to be water resistant of course which takes me back to UPVC wall board. Link to comment Share on other sites More sharing options...
blackrose Posted February 26, 2022 Author Report Share Posted February 26, 2022 (edited) 25 minutes ago, The Happy Nomad said: Sorry but I cannot agree. The simple fact is you appear to have bought the wrong toilet for the intended installation. A simple short bulkhead would have been easy to construct compared to what you now need to do. You also need to make something to mount the switch panel. With the correct choice of loo you wouldn't need to that as it's incorporated into the casing. Well then we will have to agree to disagree, but since it's my boat and my choice of toilet it's not the wrong toilet for my intended installation. Your suggestion would have been wrong because I don't like the look of the high back bulkhead toilet and I definitely didn't want a freestanding bulkhead inside my bathroom. I think they both look awful. As I said in my original post, the switch panel will be mounted into the boxing-in of the hose behind the toilet. That doesn't seem overly difficult. 9 minutes ago, The Happy Nomad said: Ah right so that cabinet does move out the way. This wasn't totally clear earlier. Then you could permanently fit a box/hood over the cassette end that mates up to where the cabinet sits. It would need to be water resistant of course which takes me back to UPVC wall board. I will have a look at UPVC wall board - hadn't considered that, thanks. But the cover for the end of the cassette only needs to be about 20cm wide, not all the way up to the where the cabinet sits. Edited February 26, 2022 by blackrose Link to comment Share on other sites More sharing options...
Guest Posted February 26, 2022 Report Share Posted February 26, 2022 Just now, blackrose said: Well then we will have to agree to disagree, but since it's my boat and my choice of toilet it's not the wrong toilet for my intended installation. Your suggestion would have been wrong because I don't like the look of the high back bulkhead toilet and I definitely didn't want a freestanding bulkhead inside my bathroom. I think they both look awful. As I said in my original post, the switch panel will be mounted into the boxing-in of the hose behind the toilet. That doesn't seem overly difficult. Of course it is I'll leave you to it. Link to comment Share on other sites More sharing options...
blackrose Posted February 26, 2022 Author Report Share Posted February 26, 2022 3 minutes ago, The Happy Nomad said: Of course it is I'll leave you to it. Thank you for your suggestions anyway. I'll post a picture once it's finished. Link to comment Share on other sites More sharing options...
blackrose Posted February 27, 2022 Author Report Share Posted February 27, 2022 (edited) Job done. I bought two of those toilet roll storage boxes that nbfiresprite suggested from Argos for a tenner each and did a bit of cutting with a jigsaw. It's not perfect but I think it's ok. Certainly better than coming into the bathroom and being faced by an ugly bulkhead & hatch because it leaves the bathroom area open. For me it was much easier than making a bulkhead too. The boxes are MDF so not waterproof but they're splash-proof and I'll paint the cut edges. I'm not intending for them to get soaked but if they don't last I can just buy a couple more and do the same thing in a few years time. I've got other MDF bathroom cabinets that have been in my bathroom for more than 15 years. The end of cassette cover just lifts away to get the cassette out. Edited February 27, 2022 by blackrose 4 Link to comment Share on other sites More sharing options...
Jon57 Posted February 27, 2022 Report Share Posted February 27, 2022 2 hours ago, blackrose said: Job done. I bought two of those toilet roll storage boxes that nbfiresprite suggested from Argos for a tenner each and did a bit of cutting with a jigsaw. It's not perfect but I think it's ok. Certainly better than coming into the bathroom and being faced by an ugly bulkhead & hatch because it leaves the bathroom area open. For me it was much easier than making a bulkhead too. The boxes are MDF so not waterproof but they're splash-proof and I'll paint the cut edges. I'm not intending for them to get soaked but if they don't last I can just buy a couple more and do the same thing in a few years time. I've got other MDF bathroom cabinets that have been in my bathroom for more than 15 years. The end of cassette cover just lifts away to get the cassette out. Nice job. Sometimes it pay to think outside the box sort of speech. 👍😜 Link to comment Share on other sites More sharing options...
Puffling Posted February 27, 2022 Report Share Posted February 27, 2022 Looks neat and does exactly the job it should. Shame the slot remaining in the top of the box can't be used to dispense paper; it's now in a better position when seated than the roll holder on the wall behind. 1 Link to comment Share on other sites More sharing options...
blackrose Posted February 27, 2022 Author Report Share Posted February 27, 2022 That slot is just a hand hold to pick up the whole unit and move it out the way when removing the cassette. Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now