Way back when we purchased stock when Kingfisher went into liquidation and, subsequently, bought engines and gearboxes from Fuzhou Engine Works until they closed. We still have in stock some engines and components but we would need to relist what we have as we have lost the computer file

We have a Euro pallet sized box -3 ft high full of parts. There are definitely no starter motors or water pumps or head gaskets (except for KD6 & KD14 + 1 bent one for KD36). There should still be a few injectors complete, injector nozzles, fuel injection pump elements, fuel injection pumps, fuel lift pumps, cylinder liners, piston ring sets, valves, valve guides. valve springs, pistons, bearing shells, oil pump, Clutch plates for MA100 gearboxes, Etc.etc.

2 6HP (KD6) single cylinder horizontal engines and manual gearboxes.
2 or 3 14HP (KD14) 2 cylinder horizontal engines with MA100 hydraulic gearboxes.
1 14HP (KD14) 2 cylinder horizontal engine with MA100 gearbox less cylinder head and starter motor.
1 295CMA (KD26) 2 cylinder 26HP engine coupled to 12.5 kva generator.

The engines are not dressed as per Kingfisher build - they are the base units as imported by Kingfisher into the UK which they dressed to their specifications.

All of these have been stored in our warehouse for a few years.

Any interest - in bits and bobs or a sensible bid to take the lot would be considered.

Although this topic has been reported as unauthorised advertising, I am minded to leave it for the time being as the content appears genuine and it may be useful to forum members who may need Kingfisher parts.

I am happy for the thread to remain.

+ 1

Would you have a 16a gearbox or clutch plates?

If the OP supplies contact details how about putting them in Links and putting a pointer to the entry for here.

I need a 67, a 23, a 34, and a 31 with fried rice.

We did not intend to do anything untoward - just that we were told that there were people on this site asking about parts - just trying to put users in touch with what parts we still have available.

If the OP supplies contact details how about putting them in Links and putting a pointer to the entry for here.

Our contact details are as follows:

 

Ajay Trading Limited

Dyers Boatyard

131 St Denys Road

Southampton

SO17 2JY

 

Tel: 023 8039 9677 Fax: 023 8039 9678 E-mail: [email protected]

Would you have a 16a gearbox or clutch plates?

Sorry - can't help with that - we only had 06 gearboxes and the single cylinder horizontals and all our bigger engines had MA100 or MA125 hydraulic boxes fitted.

Any kd14 parts or engine available I know many yrs old long shot

You would be better off going direct, the original poster has not been back since August 2013.

 

Good luck and welcome to the forum

do you have any kd36 head gaskets?

@captainshifty last logged in to CWDF in March, so there is a chance this will be seen. Have tagged them to be sure.

great thank you

We are sorry to say that we have closed down our engine warehouse and sold all of our remaining stock- the party we sold the Chinese engine parts to exported them and they are no longer available.

Do you have any kd36 cylinder heads? 

Sorry- but as in the post above we no longer have any Kingfisher or Chinese engine parts available for sale.

There are two Kingfisher engines advertised for sale in Junes Towpath + copper head gasket and gearbox bits £850  07808 211991 if people are still looking for bits

@GMOnTheCut

Edited May 30, 20251 yr by ditchcrawler

Hello, I have a kingfisher kd14 available with gearbox, spare head gaskets, spare starter motor. Engine runs but I think mostly on one cylinder. Been a problem engine for sure but I'm hoping there's someone out there who's looking for one to rebuild or cannibalise?