blackrose Posted July 18, 2018 Report Share Posted July 18, 2018 I'm just primed my stem deck with jotamastic 87 epoxy after taking it back to metal. I want to paint the aluminium generator locker and was going to etch prime it, but where the epoxy deck paint has gone over onto the aluminum at the bottom it seems rock solid. Can I prime aluminum with epoxy rather than an etch primer? I didn't think that was supposed to work? Link to comment Share on other sites More sharing options...
Boater Sam Posted July 18, 2018 Report Share Posted July 18, 2018 It will probably flake off if there is no etch primer when the aluminium gets its surface corrosion back. Link to comment Share on other sites More sharing options...
blackrose Posted July 19, 2018 Author Report Share Posted July 19, 2018 4 hours ago, Boater Sam said: It will probably flake off if there is no etch primer when the aluminium gets its surface corrosion back. But how could the aluminium get its surface corrosion back if it's been painted and there's no oxygen on its surface to react? You might be right but I think I'll key a bit more, paint it and do a proper test. Link to comment Share on other sites More sharing options...
Jen-in-Wellies Posted July 19, 2018 Report Share Posted July 19, 2018 Surface corrosion on aluminium takes place almost instantly on exposure to air. It is a thin aluminium oxide layer, strongly bonded to the underlying metal that then inhibits further corrosion. It looks like uncorroded metal to us. Anodised aluminium is a process where the oxide film is deliberately made thicker. Generally aluminium takes paint well. Anodised takes it better. Shouldn't need an etch primer. Just clean, degrease and dry the surface. Bad corrosion of aluminium is mostly when it is in contact with other metals, eapecially steel fasteners. The aluminium acts as an anode and corrodes, protecting the steel. Over time you do get the white dusty corrosion products on the surface of aluminium, but the underlying metal is sound. Jen Link to comment Share on other sites More sharing options...
blackrose Posted July 20, 2018 Author Report Share Posted July 20, 2018 (edited) Everything you say seems correct apart from not needing an etch primer? I once painted the new aluminium canopy of a passenger boat in sections by abrading, spirit wiping with the thinners for the primer and then applying an etch primer within 20 mins. So I thought aluminium did require an etch primer otherwise it wouldn't last? My original question was about epoxy because it appears to work, but whether it lasts I have no idea. https://www.austenknapman.co.uk/blog/faqs/a-3-step-guide-to-painting-aluminium/ Edited July 20, 2018 by blackrose Link to comment Share on other sites More sharing options...
Iain_S Posted July 20, 2018 Report Share Posted July 20, 2018 On 19/07/2018 at 06:59, Jen-in-Wellies said: (snip) The aluminium acts as an anode and corrodes, protecting the steel. Over time you do get the white dusty corrosion products on the surface of aluminium, but the underlying metal is sound. Tell that to my Landrover! 1 Link to comment Share on other sites More sharing options...
George and Dragon Posted July 20, 2018 Report Share Posted July 20, 2018 4 minutes ago, Iain_S said: Tell that to my Landrover! Birmabright is a special case perhaps although, to be fair, once you point out to MOT testers that it's the aluminium that's corroded and the seat belt anchors are on solid steel they have to look for another reason to fail the vehicle. Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now