Search the Community
Showing results for tags 'hot water system'.
-
Hi all 👋, first post on here but probably one of many, I'm currently looking into the heating system I am going to install on my widebeam i was hoping you could take a look and tell me what you think and if it all looks ok. (Heating sorce: Solid fuel fire and diesel water heater Heating up - radiators, under floor heating and hot water) I am thinking of installing the bubble b1c1 corner stove with back boiler, also what are peoples thoughts on the Prity AM 12 ( https://fireplacesforhome.com/Wood-Burning-Stove-Corner-Model-Fireplace-Log-Burner-Solid-Fuel-Prity-AM-12kw ) multifuel stove? And also a webasto diesel water heater. All my heating appliances are going to run to the NRG zone 5 manifold wich does allow thermosyphon , I plan to have 4x radiators, underfloor heating and calorifier attached. The diagram is missing the PRV and the pipes from the back boiler to the heating manifold will be in 28mm. My biggest worry is the thermosyphon safety as it is going to run to the heating manifold so i dont have any heat leak. Any input would be appreciated. Kind regards Brad I've linked the NRG zone let me know what you think to using this as I can't see any post speaking about this or any manifold. https://www.nrgawareness.com/product/nrg-zone-4-5-6-32-32-28/
- 8 replies
-
- back boiler
- multifuel
-
(and 25 more)
Tagged with:
- back boiler
- multifuel
- stove
- nrg zone
- thermosyphon
- gravity feed
- gravity circulation
- hot water system
- radiators
- fire
- fire safety
- widebeam
- narrowboat
- diagram
- dhw
- calorifer
- heating
- underfloor
- underfloor heating
- header tank
- hot water heating
- hot water manifold
- gravity
- pressure relief valve
- prf
- stove boiler
- hot water savings
-
Hello all! I have a Morco F11E water heater. Every time I start it all the flames ignite but go out either immediately or after a few seconds. It then tries to relight but only one or two flames will light around the ignition. In the relighting stage I can manually light all the others with a handheld flame. Seems to me there are two problems, the gas flow shutting down and the ignition failing to light fully after the first try. Any ideas? I've cleaned out the water filter and pumped up the accumulator and the water flow sensor stays on while running so i don't think it's a water pressure issue, more likely gas pressure? Thanks in advance!
- 9 replies
-
- morco
- water heater
-
(and 4 more)
Tagged with:
-
Hi peeps! I'm hatching a plan to expand our current Squirrel-fed radiator system to also heat the calorifer. I have about zero plumbing knowledge... so the ideas below are all based on assumptions. I hope that by showing you the idea at this stage, I might not make hideous mistakes! I intend to use the newer 'push fit' pipes and fittings, as they're easier, not that much more expensive than copper, and the links to the calorifier already use them. I'd also like to have a solar collector as an option. As far as I can tell, the calorifier only has one coil (unless the other one is hidden beneath its insulation.) The drawing shows the boat as if it were just one continuous wall. I.e., port, stern, and starboard. This is because the calorifier is on the port side, and the burner/radiators are on the starboard side. I have to find a way to get the feed and return either around the back of the engine bay, or along the bulkhead dividing the bay and the living space, but beneath the doorway. The circles with crosses are taps - or three-way selectors, which I'm assuming exist. The bulkhead appears twice (port and starboard) The existing system has a bolan pump, but can also be used as a thermosyphoning system. I've sent the hot feed around the back of the boat, thinking that this might continue to operate (even though the cold return from the calorifier must travel uphill by about 100mm to rejoin the radiator system. An issue with this solution is that the pipe may loose too much heat to the hull / uninsulated engine bay. Another is: how do you mount pipes onto steel hulls! If thermosyphoning, or just running from one pump isn't an option, it might be more sensible to run the hot and cold feeds from the radiator system to the calorifier along the same route that the cold feed takes in this design- along the bulkhead (3d sketch might make more sense....) I suppose that's my main question at the moment. Is is a feasible idea? and, if so, should I run the pipes around the back of the boat (pictured), in a more gentle slope, or just go for the steep attack, use less pipe, but need a pump? The hot feed could be teed from the pipework just below the header tank instead. But would the single bolan (?) pump by the Squirrel be able to move the water that far? Assumptions. The original hot/cold pipes from the engine only have one shut off valve. It's my understanding that the pressure of the water in a circuit will prevent water from a different circuit from entering it when the tap is closed: water always follows the path of least resistance. For the solar circuit, there is a pump out there that will run on 12v, not consume insane amounts of power (though, on sunny days, our panel produces at least 8A), and be able to push the cold feed water to the roof. I require a separate header tank for the solar circuit, as it's higher than the current one. The solar circuit needs to be treated as a separate system, as if connected, pressure will release water from the lower header tank. Any help or suggestions on how this could be made better, or if it will even work, most appreciated!
- 12 replies
-
- hot water system
- solar
-
(and 2 more)
Tagged with:
-
Hi, i'm new to the forum, fitting out my own boat currently! My horizontal calorifier is fitted and fed by a webasto and the engine take off hoses for heat, twin coil, and connected to accumulator and expansion tank just after the hot water out pipe from the calorifier. I only get 2 litres or so of hot water before it becomes cold, checked and bled the coolant side of the circuit, all fine, adjusted the thermostatic mixer valve to make sure it's not all cold mixing in. Water does come through from the hot tank, just a very small amount, so unlikely to be a blockage as water is flowing from the tank...im at a loss, any ideas??
- 22 replies
-
- hot water system
- heating
-
(and 1 more)
Tagged with: