Steve Manc Posted May 22, 2018 Report Share Posted May 22, 2018 Hi I recently was unable to use a mooring on Macclesfield Canal due to the narrowboat hull rubbing against a cill. Later on as I was walking past I noticed another narrowboat moored there. I looked down between the towpath and their boat and they had small wheels. I understand them to be cart wheels, around 9 inches plus, that a delivery person would have on their cart. Midland has a plastic type: https://www.midlandchandlers.co.uk/store/category/1535/product/af-184.aspx simular type on ebay: https://www.ebay.co.uk/itm/10-Pneumatic-Wheels-for-Sack-Truck-Trolley-Dolly-Cart-Garden-Barrow-PAIR-TE20/400680639947?epid=1212039937&hash=item5d4a6d5dcb Anyone using them? Any advise where to buy them? Thanks Link to comment Share on other sites More sharing options...
Nightwatch Posted May 22, 2018 Report Share Posted May 22, 2018 Yes, we use them on Nightwatch. In fact we lost one a couple of years ago. Wasn't my fault, someone?? didn't secure it to the boat! Link to comment Share on other sites More sharing options...
frangar Posted May 22, 2018 Report Share Posted May 22, 2018 I use wheelbarrow wheels. Sometimes on offer at Aldi/Lidl but always available at Toolstation or Screwfix Link to comment Share on other sites More sharing options...
Rob-M Posted May 22, 2018 Report Share Posted May 22, 2018 I have a couple of wheelbarrow wheels which I put brass eye bolts through to attach them with. Don't use them often but handy when you need to keep well away from the edge. Link to comment Share on other sites More sharing options...
Tacet Posted May 22, 2018 Report Share Posted May 22, 2018 The Midland Chandler's version, for which you provide a link, is something different. It is a more conventional fender in the style of a tyre. It has a hole to one edge for dangling from a rope. It might not float horizontally - or at all. Link to comment Share on other sites More sharing options...
Steve Manc Posted May 22, 2018 Author Report Share Posted May 22, 2018 All Thanks for the speedy replies ? Link to comment Share on other sites More sharing options...
Steve Manc Posted May 22, 2018 Author Report Share Posted May 22, 2018 Rob, Frangar, Nightwatch Which type are you or have you used Pneumatic, solid, foam filled ? Thanks Link to comment Share on other sites More sharing options...
Ray T Posted May 22, 2018 Report Share Posted May 22, 2018 (edited) How about this set up? Just make a cantilever mechanism to lower the wheels to water level. Edited May 22, 2018 by Ray T 1 Link to comment Share on other sites More sharing options...
Alan de Enfield Posted May 22, 2018 Report Share Posted May 22, 2018 (edited) 46 minutes ago, Steve Manc said: I recently was unable to use a mooring on Macclesfield Canal due to the narrowboat hull rubbing against a cill. The same cill is also found on the Shroppie (called the Shroppie Shelf) and at some locks on the River Trent. 3x Wheelbarrow wheels (with tyres) laid horizontally (front centre and back) make it all OK. Edited May 22, 2018 by Alan de Enfield Link to comment Share on other sites More sharing options...
Robbo Posted May 22, 2018 Report Share Posted May 22, 2018 10 minutes ago, Steve Manc said: Rob, Frangar, Nightwatch Which type are you or have you used Pneumatic, solid, foam filled ? Thanks I would use Pneumatic as you can then pump up to a pressure thats comfortable for the boat to rub up against. Link to comment Share on other sites More sharing options...
Nightwatch Posted May 22, 2018 Report Share Posted May 22, 2018 Our remaining one is showing wear and tear (rust) so we need to replace. I think they are probably wheelbarrow wheels. Pump up ones, can't spell pneumatic, 1 Link to comment Share on other sites More sharing options...
system 4-50 Posted May 22, 2018 Report Share Posted May 22, 2018 I use 3 x 17" alloy road wheels (3mm tread) as the shroppie shelf is quite large where I moor. They are wonderful for a quiet night's sleep. I used to use the wheelbarrow wheels but they were not always big enough and they didn't last forever. Link to comment Share on other sites More sharing options...
Flyboy Posted May 22, 2018 Report Share Posted May 22, 2018 (edited) 33 minutes ago, Steve Manc said: Rob, Frangar, Nightwatch Which type are you or have you used Pneumatic, solid, foam filled ? Thanks I use this pneumatic type, very handy for mooring on curves. Put the rope through the centre so that the wheel floats flat. https://www.ebay.co.uk/itm/4-x-10-pneumatic-wheel-with-centre-plastic-hub-jockey-wheel-cart-trolley-barrow/282294812218?hash=item41ba14fe3a:g:1KkAAOSwJ7RYVZC4 Edited May 22, 2018 by Flyboy Link to comment Share on other sites More sharing options...
Steve Manc Posted May 22, 2018 Author Report Share Posted May 22, 2018 To all Thanks for the feed back. I have ordered two pneumatic / pump up type Link to comment Share on other sites More sharing options...
WJM Posted May 22, 2018 Report Share Posted May 22, 2018 When I moor against an edge that might snag the boat, I put a boat pole down vertically between the boat and the edge, lashed to the fender attachment. That way I am protected from very large changes in level. 1 Link to comment Share on other sites More sharing options...
zenataomm Posted May 22, 2018 Report Share Posted May 22, 2018 I have often considered fitting wheels to my boat, mainly because both The Coventry and The Ashby have depleted floatability installed. 2 hours ago, system 4-50 said: I use 3 x 17" alloy road wheels (3mm tread) as the shroppie shelf is quite large where I moor. They are wonderful for a quiet night's sleep. I used to use the wheelbarrow wheels but they were not always big enough and they didn't last forever. I can't think of a single thing that does, except perhaps, disappointment. Wow that was heavy for a Tuesday!! Link to comment Share on other sites More sharing options...
system 4-50 Posted May 22, 2018 Report Share Posted May 22, 2018 3 hours ago, system 4-50 said: I use 3 x 17" alloy road wheels (3mm tread) as the shroppie shelf is quite large where I moor. They are wonderful for a quiet night's sleep. I used to use the wheelbarrow wheels but they were not always big enough and they didn't last forever. I should have said, floating flat, as Flyboy posted above. Link to comment Share on other sites More sharing options...
nb Innisfree Posted May 22, 2018 Report Share Posted May 22, 2018 Metal wheels rust (believe it or not) Plastic is better. Our stern used to bump the Shroppie ledge when moored with car wheels and tyres, unless they are from a very big car or Land rover they are 24" diameter which were a tad small for us with a standard narrowboat. Maybe standard wheels with large aspect ratio tyres might do it, say 80%, or ideally 100% but I doubt there is such a thing now. Link to comment Share on other sites More sharing options...
system 4-50 Posted May 22, 2018 Report Share Posted May 22, 2018 Link to comment Share on other sites More sharing options...
Bod Posted May 22, 2018 Report Share Posted May 22, 2018 I've got a pair of the non floating solid fenders, that have longer ropes, that are adjusted to be between the boat and shelf. Bod Link to comment Share on other sites More sharing options...
JamesFrance Posted May 22, 2018 Report Share Posted May 22, 2018 5 hours ago, Flyboy said: I use this pneumatic type, very handy for mooring on curves. Put the rope through the centre so that the wheel floats flat. https://www.ebay.co.uk/itm/4-x-10-pneumatic-wheel-with-centre-plastic-hub-jockey-wheel-cart-trolley-barrow/282294812218?hash=item41ba14fe3a:g:1KkAAOSwJ7RYVZC4 I used to have the same ones 20 years ago, bought from a garden center, if you use a fairly thick rope it just needs a knot at the end and the wheels are plastic so nothing to rust. Link to comment Share on other sites More sharing options...
Theo Posted May 22, 2018 Report Share Posted May 22, 2018 10 hours ago, WJM said: When I moor against an edge that might snag the boat, I put a boat pole down vertically between the boat and the edge, lashed to the fender attachment. That way I am protected from very large changes in level. Like what they had/have on the Middlewich Branch? Link to comment Share on other sites More sharing options...
Steve Manc Posted May 24, 2018 Author Report Share Posted May 24, 2018 On 22/05/2018 at 13:24, nb Innisfree said: Metal wheels rust (believe it or not) Plastic is better. Our stern used to bump the Shroppie ledge when moored with car wheels and tyres, unless they are from a very big car or Land rover they are 24" diameter which were a tad small for us with a standard narrowboat. Maybe standard wheels with large aspect ratio tyres might do it, say 80%, or ideally 100% but I doubt there is such a thing now. On 22/05/2018 at 10:38, Steve Manc said: To all Thanks for the feed back. I have ordered two pneumatic / pump up type Hi My pneumatic / pump up type wheels have arrived. https://www.ebay.co.uk/itm/400680639947 The air intake connector looks to be the same type as a car but smaller. Have users of these wheels used the car garage to get tyres up to 30 PSI or purchased a pump? Thanks Link to comment Share on other sites More sharing options...
nb Innisfree Posted May 24, 2018 Report Share Posted May 24, 2018 19 minutes ago, Steve Manc said: Hi My pneumatic / pump up type wheels have arrived. https://www.ebay.co.uk/itm/400680639947 The air intake connector looks to be the same type as a car but smaller. Have users of these wheels used the car garage to get tyres up to 30 PSI or purchased a pump? Thanks I used a cheap 12v tyre pump, available from various outlets, Lidl and Aldi sell them occasionally. Link to comment Share on other sites More sharing options...
Flyboy Posted May 24, 2018 Report Share Posted May 24, 2018 28 minutes ago, Steve Manc said: Hi My pneumatic / pump up type wheels have arrived. https://www.ebay.co.uk/itm/400680639947 The air intake connector looks to be the same type as a car but smaller. Have users of these wheels used the car garage to get tyres up to 30 PSI or purchased a pump? Thanks They are normally the same as a car valve. Maybe yours fit a bike pump. Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now