W+T Posted September 25, 2017 Report Share Posted September 25, 2017 I think i got a good deal here for the galley worktop at £30 fro these two lengths of hardwood and 27mm thick, perfic But as i am no joiner and the seller stated it is either Iroko or Mahogany and was an old science school work bench, and i think it could be Teak, what the hell do i know though lol. Throw your thoughts at this then folks. Other/bottom side Link to comment Share on other sites More sharing options...
Bee Posted September 25, 2017 Report Share Posted September 25, 2017 Well its brown so quite likely 'mahogany' but there's a few different types of 'mahogany' Don't think its teak as teak is greyish but I've just repaired a brown door with a bit of teak offcut and stained it and it looks pretty much identical to the brown wood. Nice bit of wood though. 1 Link to comment Share on other sites More sharing options...
WotEver Posted September 25, 2017 Report Share Posted September 25, 2017 Possibly iroko or sapele imho. Doesn’t look like teak to me. Does it matter? It’s a lovely bit of wood You’ll soon know if it’s teak and you try to glue it - the glue won’t stick 1 Link to comment Share on other sites More sharing options...
W+T Posted September 25, 2017 Author Report Share Posted September 25, 2017 Certainly doenst matter what it is as i was prepared to pay near £150, mite go back as he has another few 2m lengths and a massive slab about 240x60x40 I need to work out abotu what to do now with it, said i am no joiner, it has a crack when it as separated which i think if i read correctly i can fill it with filler of the correct colour. Should i cut it to the template then sand back and plane if need be, or sand/plane then cut to template. Does it matter? Link to comment Share on other sites More sharing options...
Murflynn Posted September 25, 2017 Report Share Posted September 25, 2017 (edited) there is such a variety of figuring in mahogany and iroko that it would be difficult to give a definitive answer, but unless it's been stained red it ain't teak. most people including Robbins (the marine timber specialists) pronounce sapele sapeelee; when I worked in Nigeria we used to spend sundays at the Sapele country club (swimming, golf, tennis) and can confirm that the local pronunciation is sapelly. Edited September 25, 2017 by Murflynn Link to comment Share on other sites More sharing options...
W+T Posted September 25, 2017 Author Report Share Posted September 25, 2017 4 minutes ago, Murflynn said: there is such a variety of figuring in mahogany and iroko that it would be difficult to give a definitive answer, but unless it's been stained red it ain't teak. most people including Robbins (the marine timber specialists) pronounce sapele sapeelee; when I worked in Nigeria we used to spend sundays at the Sapele country club (swimming, golf, tennis) and can confirm that the local pronunciation is sapelly. Keeping off topic But when you Sapele and Sapeelee it sound sthe same, depends on how fats you talk init. Now Sapelly, i like that word ;0 Cant beat my fav word Moist Oh on topic, i will give a quick sand this week and see what its like underneath. Link to comment Share on other sites More sharing options...
Victor Vectis Posted September 25, 2017 Report Share Posted September 25, 2017 An old school woodwork teacher I used to (try to) work with would have said it's one of the bastard mahoganys (referring to it's parentage not it's working properties!) Whatever it is, if it's from a school science workbench it will be good stuff. 1 Link to comment Share on other sites More sharing options...
bizzard Posted September 25, 2017 Report Share Posted September 25, 2017 (edited) Afromosia used to be the Mahogany substitute, most top quality marine ply was made from it. Most school furniture was-is made from Beech. Edited September 25, 2017 by bizzard 1 Link to comment Share on other sites More sharing options...
WotEver Posted September 25, 2017 Report Share Posted September 25, 2017 44 minutes ago, W+T said: Should i cut it to the template then sand back and plane if need be, or sand/plane then cut to template. Definitely the latter It could even be utile but I doubt that, considering its age. 1 Link to comment Share on other sites More sharing options...
W+T Posted September 25, 2017 Author Report Share Posted September 25, 2017 Ok i had to give it a sand, and when i wippe dit down with a quick damp rag of acetone it look sweet as hell. Link to comment Share on other sites More sharing options...
Bee Posted September 25, 2017 Report Share Posted September 25, 2017 I wouldn't try to plane it as it will tear out the grain and make a mess. Does look a little bit stripey in places - Sapele looks stripey but I think Victor Vectis probably has it right. Link to comment Share on other sites More sharing options...
36national Posted September 25, 2017 Report Share Posted September 25, 2017 Old school workbenches or even "old school" workbenches if used in science labs as opposed to woodworking shops were made of teak. This is because all the nasty chemicals you used to be able to use in chemistry lessons couldn't destroy the fu**er. To me (in the sanded photo) teak looks like what you got. I'm a chemist not a woodworker. I take it the indestructible element is good. Acetone will clean it but even though its an aggressive solvent it not attack it (hence the use in chemistry labs). I have used danish oil on teak (don't varnish, it looks nice but the wood is harder wearing than the varnish which defeats the object) but been told that Tung oil is better. oh yeah and you won't plane it, just try 2 Link to comment Share on other sites More sharing options...
W+T Posted September 25, 2017 Author Report Share Posted September 25, 2017 2 minutes ago, 36national said: Old school workbenches or even "old school" workbenches if used in science labs as opposed to woodworking shops were made of teak. This is because all the nasty chemicals you used to be able to use in chemistry lessons couldn't destroy the fu**er. To me (in the sanded photo) teak looks like what you got. I'm a chemist not a woodworker. I take it the indestructible element is good. Acetone will clean it but even though its an aggressive solvent it not attack it (hence the use in chemistry labs). I have used danish oil on teak (don't varnish, it looks nice but the wood is harder wearing than the varnish which defeats the object) but been told that Tung oil is better. I was planning to use this as i have been told and read is is great for this job. https://www.letonkinoisvarnish.co.uk/varprices.html There is some debate now as to what it is, Utile which Tony says ( Whatever ) what it could be is a new one to me. Link to comment Share on other sites More sharing options...
Cheshire cat Posted September 25, 2017 Report Share Posted September 25, 2017 Presumably his jigsaw blades are going to become blunt pretty quickly too. I'll give you a tenner for it. You can buy a lot of balsa for a tenner. Link to comment Share on other sites More sharing options...
WotEver Posted September 25, 2017 Report Share Posted September 25, 2017 I wouldn’t worry about what it is unless you need to glue it. If you do and it is teak it won’t stick without first cleaning the faces with acetone. Other than that, just enjoy its beauty Le Tonkenois is just as fine on teak as it is on mahogany. Link to comment Share on other sites More sharing options...
36national Posted September 25, 2017 Report Share Posted September 25, 2017 what job ? the link refers to varnish its up to you but varnish tends to age and crack. this means you gotta sand and re-coat. If you use oil or polish all you gotta do is re oil or re-polish. Link to comment Share on other sites More sharing options...
WotEver Posted September 25, 2017 Report Share Posted September 25, 2017 (edited) 16 minutes ago, W+T said: Utile is a new one to me. You’ve seen utile on Colin’s dogbox: 6 minutes ago, 36national said: the link refers to varnish its up to you but varnish tends to age and crack. this means you gotta sand and re-coat. If you use oil or polish all you gotta do is re oil or re-polish. No, the link refers to Le Tonkenois, which does not age or crack. It is a tung oil based product. I suggest you read the info on their site if you are unaware of the product. Edited September 25, 2017 by WotEver Clarity 1 Link to comment Share on other sites More sharing options...
Sea Dog Posted September 25, 2017 Report Share Posted September 25, 2017 6 minutes ago, WotEver said: You’ve seen utile on Colin’s dogbox: Ooh, there's that box again - it genuinely is the dog's, isn't it! 1 Link to comment Share on other sites More sharing options...
tree monkey Posted September 25, 2017 Report Share Posted September 25, 2017 Just to say, I have no idea what timber that is but its beautiful, that will make a lovely worktop 1 Link to comment Share on other sites More sharing options...
rasputin Posted September 25, 2017 Report Share Posted September 25, 2017 my money is on teak, i had a load of that from a shop display unit, got stolen at the sailing club sadly... Link to comment Share on other sites More sharing options...
WotEver Posted September 25, 2017 Report Share Posted September 25, 2017 A mate of mine got a length of workbench from the old power station at Gravelly Hill and he made an electric guitar out of it. It was definitely either mahogany or one of the clones. Wayne’s lump of timber could indeed be teak as the appearance of freshly prepared teak isn’t that far removed from mahogany (dependant on the grain type). Most mahoganys will have a reddish tint whereas teak will be brownish or even yellowish. As I said earlier the only real difference that could affect him is glueing it. Oh, and if it is teak it’ll blunt his saws quickly. Link to comment Share on other sites More sharing options...
BWM Posted September 25, 2017 Report Share Posted September 25, 2017 Looks like iroko, fairly standard for science lab tops. Link to comment Share on other sites More sharing options...
sharpness Posted September 25, 2017 Report Share Posted September 25, 2017 (edited) 45 minutes ago, WotEver said: Oh, and if it is teak it’ll blunt his saws quickly. And it will blunt the plane quickly & tear out as the grain goes in so many different directions in a very short space. ETA I think its teak looking at the grain, the colour can be anything you want to stain it but you cant alter the grain. Edited September 25, 2017 by sharpness Link to comment Share on other sites More sharing options...
rasputin Posted September 25, 2017 Report Share Posted September 25, 2017 be careful of the sawdust as in, not breathing it in Link to comment Share on other sites More sharing options...
WotEver Posted September 25, 2017 Report Share Posted September 25, 2017 12 minutes ago, sharpness said: And it will blunt the plane quickly & tear out as the grain goes in so many different directions in a very short space. As will many cuts of mahogany. I had to spend a lot of time with belt sanding then RO sanding and then finally scraping the wide end pieces of utile on that dogbox. They were impossible to plane even with a low angle and super sharp iron. Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now