John Barnet Posted April 6, 2011 Report Share Posted April 6, 2011 Hello I need to remove 20 years of hull tar blacking and start afresh. The boat is in the Midlands, can anyone recommend someone for the job. thanks Link to comment Share on other sites More sharing options...
Jo Gilbertson Posted April 6, 2011 Report Share Posted April 6, 2011 Hello I need to remove 20 years of hull tar blacking and start afresh. The boat is in the Midlands, can anyone recommend someone for the job. thanks Hi I had a problem with my blacking and someone suggested needle gunning it off - Stockton Dry Dock Co can do this(Stockton Warks GU) (01926814441, E.mail Graeme graeme@stockton-dry-dock-company.co.uk). Not sure where you are in relation - might be other closer yards that could do the same? Link to comment Share on other sites More sharing options...
Chertsey Posted April 6, 2011 Report Share Posted April 6, 2011 Industry Narrowboats at Stretton Aqueduct on the Shroppie will crane out, arrange a shotblaster and do blacking - or you can do DIY blacking. If that sounds like the right area, I'll dig out the phone number for you. Link to comment Share on other sites More sharing options...
PaddingtonBear Posted April 6, 2011 Report Share Posted April 6, 2011 But be careful as the twenty years of blacking might be holding the boat together - seriously though Stretton Wharf is the place for you and very reasonably priced as well. Link to comment Share on other sites More sharing options...
blackrose Posted April 7, 2011 Report Share Posted April 7, 2011 Hi I had a problem with my blacking and someone suggested needle gunning it off - Stockton Dry Dock Co can do this(Stockton Warks GU) (01926814441, E.mail Graeme graeme@stockton-dry-dock-company.co.uk). Not sure where you are in relation - might be other closer yards that could do the same? Needle guns are good for small inaccessible areas such as internal corners, but not for removing blacking from the outside of an entire hull. I've also seen needle guns go through corroded steel that's got a bit thin so only use them on sound steel. Link to comment Share on other sites More sharing options...
Dovetail Posted April 7, 2011 Report Share Posted April 7, 2011 Hello I need to remove 20 years of hull tar blacking and start afresh. The boat is in the Midlands, can anyone recommend someone for the job. thanks I am assuming this is above the water line and not below. If it is below the water line then lucky you and keep it on my blacking seems to last two years max before it starts to fall off. Good look Link to comment Share on other sites More sharing options...
John Barnet Posted April 7, 2011 Author Report Share Posted April 7, 2011 I am assuming this is above the water line and not below. If it is below the water line then lucky you and keep it on my blacking seems to last two years max before it starts to fall off. Good look Thanks All Will Speak to Stockton as not too far -Not sure about the needle gun. 20 years does give a lot of cover, unfortuately its now so thick its starting to blister. Not so good. Shropies a bit too far but will consider at a push once again thanks for the relpys Link to comment Share on other sites More sharing options...
Timleech Posted April 7, 2011 Report Share Posted April 7, 2011 Thanks All Will Speak to Stockton as not too far -Not sure about the needle gun. 20 years does give a lot of cover, unfortuately its now so thick its starting to blister. Not so good. Shropies a bit too far but will consider at a push once again thanks for the relpys Needle gun will clog up if used extensively on tar or bitumen, plus it's a tedious job for a whole boat and there are hand vibration issues using it for long periods, but it can be done. Consider a powerful water pressure washer, a powerful industrial washer with rotary nozzle will get rid of any old paint which isn't adhering properly. Alternatively there are very high pressure systems which will get the whole thing back to bare metal without the mess of grit blasting, but you'd probably have to get contractors in to do that. Tim Link to comment Share on other sites More sharing options...
koukouvagia Posted April 7, 2011 Report Share Posted April 7, 2011 Hi I had a problem with my blacking and someone suggested needle gunning it off - Stockton Dry Dock Co can do this(Stockton Warks GU) (01926814441, E.mail Graeme graeme@stockton-dry-dock-company.co.uk). WFBCo (now Stockton Dry Dock Co.) used to shot blast boats in a shed at the extreme end of Kayes Arm. It'd be worth giving Graeme a ring to see if they still do it. Link to comment Share on other sites More sharing options...
David Mack Posted April 7, 2011 Report Share Posted April 7, 2011 Needle gun will clog up if used extensively on tar or bitumen, plus it's a tedious job for a whole boat and there are hand vibration issues using it for long periods, but it can be done. Consider a powerful water pressure washer, a powerful industrial washer with rotary nozzle will get rid of any old paint which isn't adhering properly. Alternatively there are very high pressure systems which will get the whole thing back to bare metal without the mess of grit blasting, but you'd probably have to get contractors in to do that. Tim We used a mooring spike to chip off much of old (tar) blacking, followed up with a wire brush on an angle grinder to clean up Fulbourne's hull last year. David Link to comment Share on other sites More sharing options...
Featured Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now